Jump to content
SAU Community

Recommended Posts

Hey, i've got a 2003 skyline v35. a couple of months back when it was about 40 degrees the coolent started to boil and spurted out which created havoc with the air con. ever since every now and a again when i start the car i hear this

water sloshing sound in front of the dashboard. anybody know why this happens? or experienced this before?

any advice on what i should do?

thanks a lot.

Is it still losing coolant? Sounds like maybe the heater box is leaking coolant into the ducting.

Can u smell coolant with the heater or aircon on?

hey i haven't really tested it. what is it meant to smell like? i'll try it and get back to you.

i called nissan service center and they said they won't look at it cos its an import, something about how they're computers won't sync with mine :(

i called my dealer skyimports in melbourne and they said they'll have a look on tuesday.

is it still ok to drive it around? how severe is the problem? i clearly dunno much about this.

thanks a lot btw.

hey i haven't really tested it. what is it meant to smell like? i'll try it and get back to you.

i called nissan service center and they said they won't look at it cos its an import, something about how they're computers won't sync with mine :(

i called my dealer skyimports in melbourne and they said they'll have a look on tuesday.

is it still ok to drive it around? how severe is the problem? i clearly dunno much about this.

thanks a lot btw.

the air con doesn't smell or anything but i had a look at the coolent and its almost empty...

... what is it meant to smell like?

^ ^ ^ a bit like 34 minute-old ejaculant on floor of passenger footwell :P

see if coolant is leaking behind glove box where heater core might be

shut off heater

refill coolant before driving and take spare water with you whilst driving until it's attended to on tuesday

if you arent leaking water, it means you havent bled your coolant system properly. the sound you're hearing is the water moving around in the air gaps inside the heater core. bleed your coolant properly and it should go away.

if you arent leaking water, it means you havent bled your coolant system properly. the sound you're hearing is the water moving around in the air gaps inside the heater core. bleed your coolant properly and it should go away.

hey thanks, yup there's nothing leaking atm.

i'm new to all this. is bleeding the coolant easy to do? what does it involve doing?

thanks a lot.

you need to get all of the air out of your coolant system. it involves filling up your radiator, letting the car get to operating temperature and revving the engine to about 3000rpm every now and then while still keeping the coolant topped up. you need to keep an eye on the temperature, making sure it doesnt overheat.

you need to be doing all of this while the heater is on full heat @ full fan speed. when it seems like its not releasing any more air, close the radiator cap, let it idle for a little while then crack the bleeder nut which is at the highest point of the cooling system.

if its your first attempt i suggest searching 'how to bleed cooling system'. or get it to a mechanic to sort out.

this has the potential of doing a bit of damage if temps get too high so be careful and dont be afraid to turn the car off if you feel like the temperature is getting too hot.

you need to get all of the air out of your coolant system. it involves filling up your radiator, letting the car get to operating temperature and revving the engine to about 3000rpm every now and then while still keeping the coolant topped up. you need to keep an eye on the temperature, making sure it doesnt overheat.

you need to be doing all of this while the heater is on full heat @ full fan speed. when it seems like its not releasing any more air, close the radiator cap, let it idle for a little while then crack the bleeder nut which is at the highest point of the cooling system.

if its your first attempt i suggest searching 'how to bleed cooling system'. or get it to a mechanic to sort out.

this has the potential of doing a bit of damage if temps get too high so be careful and dont be afraid to turn the car off if you feel like the temperature is getting too hot.

hey thanks for all that info.

i did go see a mechanic today. we tried running the heater on to verify the sloshing sound but nothing happened. because its intermittent and the mechanic couldn't hear it, he asked me to come

back if the coolant runs low (?). i mentioned bleeding the coolant but he said that he can't confirm anything at this point.

would you recommend getting a another mechanic to check it out?

thanks!

Edited by greenpool

Need to get the air bubbles out of the coolant mate.....happened to me with my old 180sx when I installed a new PWR radiator.

I bleed the system but it still had bubbles in the coolant, just keep bleeding it over the next couple of drives and should go away.

Also I squeezed the radiator hoses to push the air bubbles out which helps.....and you need to get the water hot enough to open the thermostat.

I normally cut a 2lite bottle in half and tape it to the top of the radiator so the water level is higher than the engine which helps push the water down.

Edited by 180JDM

get any brand but make sure its concentrated or get a 50/50 blend. some do a 30/70 on non turbo cars (30 coolant/70 water). its up to you which one you go for - its just an anti-boil/freeze additive.

you'll find that the concentrates are a little cheaper than the pre-mixed stuff.

another quick question.

i've currently got the coolant tank filled with water. above the max cos i didn't know any better lol.

when i've got the coolant, can i mix it with the water? OR wait till the water evaporates and then fill it with coolant?

thanks a lot for ya replies.

you dont need to put anything in the reservoir tank. if its over-filled then it will just drain if your fuel cap ever releases any pressure. its not something you need to fill up.

just concentrate on putting coolant into your radiator.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The trouble with phone apps is that they really do not know the sensitivity of the mic on each specific phone, whether there is some sort of cover or skin that can change that, etc etc. So the readings off them are not calibrated. You certainly couldn't be sure that you were even within 3 dB. I have the same app on two (actually more than that) different phones/tablets and the readings in the same room at the same time are never the same. I don't mind the apps - they are as useful as a dyno - if you're testing for delta from thing1 to thing2. But not to try to generate some sort of absolute value.
    • I'm gonna use the "Sound Meter" app from the Google Play Store and as close as I can bother to these procedures: 4. TEST METHOD FOR ALL VEHICLES EXCEPT PRE ADR83 IN-SERVICE GOODS VEHICLES AND OMNIBUSES 4.1 Microphone position 4.1.1 The microphone shall be directed towards the orifice of the exhaust outlet and shall be supported by a tripod or similar device not providing excessive acoustic reflection. The general requirements for positioning microphones are shown in the Appendix. 4.1.2 The nominal axis of maximum sensitivity of the microphone shall be substantially parallel to the test site surface and shall make an angle of 45 degrees ±10 degrees with the principal direction of gas flow from the exhaust. 4.1.3 In selecting the 45 degree alignment from the outlet of a motor vehicle fitted with two or more outlets, only the angle resulting in the microphone being farthest from any other outlet must be used. National Stationary Exhaust Noise Test Procedures for In-Service Motor Vehicles Page 3 4.1.4 The height of the microphone above the test site surface shall be equal to that of the orifice of the exhaust outlet ±25mm but shall not be less than 200mm above the test site surface. 4.1.5 The distance of the microphone from the exhaust outlet orifice shall be 500mm±25mm. 4.1.6 [Relates to vertical exhaust outlets] 4.1.7 For vehicles fitted with one exhaust outlet the microphone shall be placed so that the greatest possible distance is achieved between it and the vehicle. 4.1.8 [Relates to multi exhaust outlets] 4.1.9 [Relates to multi exhaust outlets] TLDR: 200mm off ground 45 degree angle relative to exhaust flow 500mm from tailpipe exit. (I probably won't use a tripod) Here's a photo, cause I read the instructions wrong myself.
    • No ABS, no TCS, no airbags, no cruise control, no lane departure assist, no emergency brake assist, no orange lights in the mirrors (continuously annoying me in multi-lane traffic), no stupid rear view camera. I am the one responsible for where my car goes and how it does it.
    • Cheapest Jaycar one is only $65.
    • Probably best way would be using a proper dB / SPL meter lol Buy one and ship it from state to state to have a consistent test device lololol  
×
×
  • Create New...