Jump to content
SAU Community

How Much Power Should I Expect?

BennyR33

By BennyR33,
in Engines & Forced Induction

 Share

Recommended Posts

BennyR33 Explorer

BennyR33

Posted
Posted

afternoon guys,

about a month ago i purchased my 1994 R33 GTS-T.

ok so the reason for this post is there is a dyno/show and shine day coming up on the 26th and i want to know a rough power figure of what i should see my car push out.

only MODS are,,

FMIC

Full exhaust from turbo back with split dump.

BOV

E-boost controller only running 8pound on all 3 stages tho, (yet to get that tuned as it come like that in the car)

any replies much appreciated.

Ben.

post-81751-0-53477700-1300090135_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/357374-how-much-power-should-i-expect/
Share on other sites
jjman Mentor

jjman

Posted
Posted (edited)

seeing as its running on the standard ECU and the series 1 ecu at that i wouldnt expect much.

if it seems to run well and pull right throughout the rev range id say 190-200hp atw,

if it does the standard ecu thing and goes really flat after about 5000rpm due to your mods n boost then i would expect less...

my feeling is that mods like exhaust and FMIC dont do much to skylines unless you have a happy ecu which i have only ever seen ahppen in a series 2 motor.

good luck n tell us what you get... Or, even better, put it on there at 7psi (stock boost) n then do another run and try throwing 10 or 12psi into it n see if it actually makes a difference. AFR chart would be awesome too...

Nice looking 33 btw

Edited by jjman
BennyR33 Explorer

BennyR33

Posted
  • Author
Posted

thanks JJMAN.

it seems to run stong the whole way through the rev range. actually seems to pick up after 5,000 i think higher boost kicks in..? im new to all this turbo stuff tho.

ill post up the dyno print out and let you all know how it goes tho! looking forward to it!

jjman Mentor

jjman

Posted
Posted (edited)

ahhh, you should see some better numbers then as you missed the key ingredient in your parts line up.

You bet the Apexi safc will make a difference. Id say you should see at least 220hp (if it was indeed tuned to 8psi). That is why it pulls hard in the upper revs. Most stock ecu R33's, n particularly S1's, really fall over in the upper revs...

So i now backtrack on my last comment ans say DO NOT WIND THE BOOST UP!!! the SAFC is a unit that needs tuning and so will have been tuned in to a certain boost level- hopefully 8psi if that is what the controller is set at. Any more boost and it is possible you will ping the motor n even kill it. Do not ever f*k with the SAFC or the boost controller.

I would reccomend you find the place that did the SAFC install and confirm what they did n to what boost (get an power graph and AFR's). If you cant find them and get this info then find a reputable SAFC tuner and go in for a retune. People have blown up motors self tuning, driving with a bad tune or upping the boost on SAFC's.

Otherwise if you are chasing more power just pull the safc and get a Power FC or Nistune etc done n go for more boost (read up on the implications of this tho). Pretty easy to get his 200's hp on 12+psi tuned.

enjoy mate

Edited by jjman
BennyR33 Explorer

BennyR33

Posted
  • Author
Posted

yer i forgot about the SAFC haha.

i would have no idea where or when it was installed. so you recomend to keep the SAFC in the car? i haven't tried to up the boost or change the settings on the SAFC as i know if i do so it could lean the engine out and so on. but i plan to get it tuned when i have the money.

ok.. what are AFR's and Power FC? im guessing the second is an after market computer?

sorry for the stupid questions but this is why i joined the forum, to learn about all this stuff (:

cheers mate.

StealthX Veteran

StealthX

Posted
Posted

yer i forgot about the SAFC haha.

i would have no idea where or when it was installed. so you recomend to keep the SAFC in the car? i haven't tried to up the boost or change the settings on the SAFC as i know if i do so it could lean the engine out and so on. but i plan to get it tuned when i have the money.

ok.. what are AFR's and Power FC? im guessing the second is an after market computer?

sorry for the stupid questions but this is why i joined the forum, to learn about all this stuff (:

cheers mate.

AFR stands for air:fuel ratio. A measure of how much fuel:air in the cylinders. its measured by an aftermarket wideband oxygen sensor, in the exhaust. 14.7:1 (14.7 parts of air to 1 part of fuel) is the golden number where all the fuel ignites and is the most efficient point for petrol engines. Under boost/load, that number should drop down to 11.0-12.0, or even lower if the car is running rich. any number higher than 14.7 is lean, and any number below 14.7 is rich.

Power FC is an engine computer made by Apex'i. One of the best options for skylines and silvias. They plug in, offer full control and are fairly easy to tune.

p.s. SAFCs are pretty average. They only alter the air flow signal to the ECU, so they are no way a good tuning device. they are good for anything less than ~190wkw. Anything more than that and SAFC really isn't a smart choice.

BennyR33 Explorer

BennyR33

Posted
  • Author
Posted (edited)

AFR stands for air:fuel ratio. A measure of how much fuel:air in the cylinders. its measured by an aftermarket wideband oxygen sensor, in the exhaust. 14.7:1 (14.7 parts of air to 1 part of fuel) is the golden number where all the fuel ignites and is the most efficient point for petrol engines. Under boost/load, that number should drop down to 11.0-12.0, or even lower if the car is running rich. any number higher than 14.7 is lean, and any number below 14.7 is rich.

Power FC is an engine computer made by Apex'i. One of the best options for skylines and silvias. They plug in, offer full control and are fairly easy to tune.

p.s. SAFCs are pretty average. They only alter the air flow signal to the ECU, so they are no way a good tuning device. they are good for anything less than ~190wkw. Anything more than that and SAFC really isn't a smart choice.

im fairly sure mine is running rich as it smells fuely.. thats why i want to get it tuned and to set up the E-boost controller properly.

so how much would a Power FC set me back and do i need to get it dyno tuned??

Edited by BennyR33
jjman Mentor

jjman

Posted
Posted (edited)

I wouldnt assume it is running rich just beacuse you can smell fuel (u might have a decat pipe or knackered cat convertor). Also you will most likely be smelling exhaust at idle which is only indicative of your idle settings and perhaps health of your air flow meter and O2 sensor. Nonethelses, it is worth getting the tune checked...

Will id say you would be lucky to get into a Power FC, installation and tune (yes they do need to be tuned) for under 2k. While a retune on your SAFC would be a few hundred bucks...

If i were you id go for the retune and see if you can stay happy with that at the max power it will give you. otherwise. Or, if you have the money, go for a nistune or Power FC n 12-14psi (270-300hp). Though dont expect your turbo to last forever at this level so factor in that...

Edited by jjman
BennyR33 Explorer

BennyR33

Posted
  • Author
Posted (edited)

I wouldnt assume it is running rich just beacuse you can smell fuel (u might have a decat pipe or knackered cat convertor). Also you will most likely be smelling exhaust at idle which is only indicative of your idle settings and perhaps health of your air flow meter and O2 sensor. Nonethelses, it is worth getting the tune checked...

Will id say you would be lucky to get into a Power FC, installation and tune (yes they do need to be tuned) for under 2k. While a retune on your SAFC would be a few hundred bucks...

If i were you id go for the retune and see if you can stay happy with that at the max power it will give you. otherwise. Or, if you have the money, go for a nistune or Power FC n 12-14psi (270-300hp). Though dont expect your turbo to last forever at this level so factor in that...

2k aye? guess that will have to wait if that's the path i want to take. but for now i got other things i want to do firstly like tinted windows and sort out a new front bumper as the GTR repica one on it now is just to damn low. makes it impractical..

but anywho here's a pic some of you might enjoy.

oh and thanks for all the replies!!

Ben.

post-81751-0-26282100-1300165875_thumb.jpg

Edited by BennyR33

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      Well, I'm tired. I'm tired because about 4PM yesterday, before today's appointment someone immediately bought my bumper. They couldn't get it any other day as they're on the way back to NSW. So I had to do that big GTR conversion I had been planning. Unfortunately, the information on SAU about what you need and how this is done is incomplete. So what should be a simple bolt on affair, yeah, it's not. Did you know if you use all GTR items the bonnet won't close? This little manuever sent me into about 1am the night before trying to dodge a way to get it closed. I will have to revisit this in the next few days  - or maybe not, I may let a body shop figure it out. It all needs to come up and my motivation to pull the bumper off is low. It also seems to hit things in the bay where the GTT bonnet didn't. Yes I used 100% new OEM GTR items. Today, I had the joy of driving to the dyno looking like this: Given I had roughed in the fuel and given sensible but pretty conservative timing, I didn't really bet on having the car drive out any real difference than when it drove in. Sadly due to a miscommunication and laptop fun and games (and almost bricking the dongle, prayers and firmware updates indeed), I ended up using HP Tuner credits to licence the car that was already licenced. So in the end my laptop was used. It turns out my butt dyno is still well calibrated after all this time. The 325kw was on 74% Ethanol, the 313kw line was on 98. The other line is the 'before' line which was 281kw. While the numbers are pretty low, they're pretty in line with what you'd expect. Even if US dynos bump the whole result up about 50KW, gaining 10-15% is similar gains.  The curve of the cam is pretty much spot on with what was discussed as well. All this said, it still feels bad to not see the number you secretly want to see. Even if the car drove great beforehand, and I knew pretty confidently the car would drive out much the same way it drove in due to the nature of a wellish dialled in LS1 not gaining much if anything at all from being tuned from where it was. As expected, the car isn't particularly sensitive to running it at anywhere between 12.0 and 13.0 - And the initial timing at 20deg and 12.0 made 308KW. So 3 degrees of timing, and leaning it out to 12.7 for 5kw, anything above stopped giving any benefit until E85 (which has an additional 2 deg as before). Car itself behaved entirely fine. I found out that 100C = 1.15V! IAT at about 7pm was 19C. I might mess with the bonnet mounting.. but given the REO NEEDS TO BE CHOPPED TO FIT A GTR BAR this is possibly something I may leave gathering (more) dust until it returns to paint jail.
    • MBS206
      NC MX5

      By MBS206 · Posted

      It sounds farrrrrrr too cold at your place Duncan... Here I was thinking our 10 degrees overnight is getting cold...
    • Duncan
      NC MX5

      By Duncan · Posted

      oh yeah, reminded this morning....bin lids frozen shut too
    • GTSBoy
      NC MX5

      By GTSBoy · Posted

      In my case not, because of total reno. But yeah.
    • FRGTN1
      R34 Manual conversion Speedometer

      By FRGTN1 · Posted

      Did you use an electronic speedo drive? Does you speedometer read all the way to 180km?
×
×
  • Create New...