Jump to content
SAU Community

Recommended Posts

  • Replies 42
  • Created
  • Last Reply

Top Posters In This Topic

Excellent, the other thread was getting out of line :D

I've got one simple question to get started......why does *anyone* want anything other than a 1 way diff? Under which circumstances do ppl want LSD affect under braking?

I saw one diagram in one issue of option jap mag suggest that 2 way help drift, since both wheels almost same speed enter apex, then driver will use conter steer to help enter conor..that's use my limited japanese. but maybe mean something else.

Also thanks to Steve post this link

How does the conventional diff work?

2 way, 1.5way or 1way?

I would think its 2 way as when compression locking two wheels lock.

Difference is I suppose the conventional diff isn't as tight.

Could a 1.5way diff actually help you corner? Possibly helping the front wheels turn in easier with less understeer? Giving a slight neutral feel if you like?!?

I am in the market for a diff soon. I was thinking about getting the stock diff shimmed up however it makes it basically a locker which is good for drift but no good for general street driving. Any one with experience how tight these shimmed diffs are would be great. I drive to Uni which = lots of U-turns or sharp turns to get in to car parks etc.

Could a 1.5way diff actually help you corner? Possibly helping the front wheels turn in easier with less understeer? Giving a slight neutral feel if you like?!?

G'day Joel,

With my limited knowledge, I would say yes provided you are accelerating.

With my 2 way, there is a definate change between off and on throttle when going around a corner (as SydneyKid has discribed).

Off throttle going into the corner it will understeer a little (but is very easy to control, and on a track you probably wouldn't be driving like that anyway), and once you start to feed the power back on you can feel the back really pushing hard and will induce a bit of oversteer (again, really easy to control).

Sounds hard, but it's very predictable and consistant.

So I'd say that a 1.5 way would tend to understeer less than the 2 way, so for the street and track a 1.5 way would be the best. Although a 2 way would still be better than the stocker.

J

P.S. - the FM901's are getting pretty low on tread of late, and I've been giving them a bit of a hand :rofl: It's only now I know how predictiable these diff are :P

Nope, the sockie is a LSD (limited slip). So with the stockie it will let both wheels spin at different speeds, but it will just limit the amount of difference between them.

Think of it like this. Stock diff is limited slip, while a 1/1.5/2 way is no slip, it'll lock the wheels to the same speed (if your accelerating enough).

I think that reshimming the stock diff will just make it tighter, so the amount of slip that it lets happen is less ?? Can some confirm this ?

J

talking about "lockers" and "LSD's" : why do they seem to go hand in hand with mechanical diffs?

eg: "OS Giken Super Lock LSD" i gather this is a locker diff, so why do they put "LSD" in the title? Isnt it either a limited slip, or a locker?

Re-shimming the stock diff can be customised by the amount or thickness of shims, to give the effect you want. Ive heard of UAS reshimmed diffs over here being great for the street. In probably most conditions other than drifting, i found my stockie to be perfectly adequate for street, and if you dont want a pig of a diff, maybe just get it tightened up a little bit? i think this is possible...

my problem is that it my diff frequenly open wheels when puttin down the power.

Sometimes when i go WOT, i get major traction problems, the car pulls slightly to a certain side to say that they wheels are spining, yet its nothin like an oversteer where the rear end really steps out, it just slighty does. Now in this situation, are both the wheels spinnin, ie can the car pull to a certain side yet only 1 wheeling?

when i turn a corner slowly my inside wheel skips and it does not make any noises at all (like clunks), and when going around rounderbouts the car feel like it is pulling back and fowards (a surging feel).

do you think this is locker? I have been told that it may be just a tight cluch, but it skips even when I'm riding the clutch a little.

Any of you guys running coilovers?

Just thought I'd mention I have recently swapped to a set of coilovers which have been corner weighted and adjusted on the previous car (R32GTSt)

I used to have a problem of spinning one wheel contantly, but after installing the coilovers, the rear seems to be alot better, more even weight on each wheel i guess

It still has its moments though, so I am about to install one of those aluminim cradle bush kits to try and help it put more power through BOTH wheels!!

The diff will be the last thing I look at, as i dont want to transform it into a pig around town and through the hills, as most of my driving is done in either one of those

my problem is that it my diff frequenly open wheels when puttin down the power.

Sometimes when i go WOT, i get major traction problems, the car pulls slightly to a certain side to say that they wheels are spining, yet its nothin like an oversteer where the rear end really steps out, it just slighty does. Now in this situation, are both the wheels spinnin, ie can the car pull to a certain side yet only 1 wheeling?

Mine does the same. Slowly its getting much worse.

Some times it is fine, I can launch with a 4200rpm and only have the wheels chirp all the way through first. Other times it will start then all of a sudden let go.

If give it a little stick on come on to boost in first while turning left, the inside left wheel will spin up and feel very gay as the car doesn't accelerate, doesn't go sideways the slightest & makes lots of noise.

The car's diff 2 years ago used to be really tight. Always sideways never open wheeled on hard cornering etc. But that was 60,000+ km's ago.. :)

Mine's got stock shocks and lowered springs, and the diff made a huge difference.

For me tho, its not about drifting around the local round about, I'm looking for traction out of corners, and the diff is great there. You can get on the gas far earlier than with my old, worn out stock diff

Mines a 1 way mechanical, and I'm very happy with it, cost me $500.

Still wondering about benefits of 2 way dif, I take the point that it may be better for drift but surely thats only a small difference (after all you are acellerating - or trying :) - when you are drifiting...) Any other benefits?

enrico, if the back end steps out, that usually means you are getting drive to BOTH wheels, but in a stock lsd like yours, you may be getting uneven power distribution, eg 70% power to your left wheel and 30%power to the right, and so it steps out just a little. So you may be openwheeling a bit. If both spin together as in a locker, you can feel the back end very consistent, and it will feel a little "floaty" as both wheels have broken traction.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Ha, well, it's been.... a bit of a journey. Things have taken much longer than I'd hoped. I'll probably put up a thread at some stage. Hopefully soon. The car's not done any kms since my update in June though, put it that way.
    • Here's the chart for fuel pressure vs. current draw, assuming your base fuel pressure is 3 bar and you run like 0.5bar boost on WOT, you should only momentarily hit 9amps here and there. (Ignore my prev post, I cannot read a chart these days it seems)
    • Those comp test results are not hideous. Whether they are accurate or not (ie, when that comp tester says 140 psi, is the real pressure120, 140 or 160?) is unknown to us. The state of the battery used to crank it over is unknown, etc etc. Many people around here would say that the absolute values and the spread are perfectly fine to just add boost and keep going. I personally would be happier with a narrower spread than that, but even the diff between 125 and 145 is not terrible. That one cylinder at 125 though, has probably copped some damage relative to the others. You should inspect the valves seeing as you've got it open. Do you know how to measure installed ring gaps? That, and an inspection of the rings themselves, is how you will determine whether they need to be replaced. If you're not good to do these things, take the block and the pistons and rings to a shop that is, and ask them for the go/no-go on them. Do the bores need a hone at all? If so, you might well be justified in getting some different pistons in order to get away from the ring supply problem. Whether you're happy to spend a lot more money right now, on more gear, rather than less money, but an amount that looks stupid given that you will only get a handful of rings in exchange for that money, is for you to decide.
    • also possibly backed up to my filler and shat down it! 🤣
    • Ok so i would love some advice here please, i purchased an R33 a few months back and its had a few mods done to the engine, its an RB25det running a Master ECU, 1200cc injectors, bigger turbo, oil cooler, oil filter relocation kit, Spool H-beam rods, acl/ross pistons. When i removed the motor from the vehicle (as its getting a respray) i thought i would compression test it and these are the following results. Cylinder 1-145psi, Cylinder 2-143psi, Cylinder 3-125psi, Cylinder 4-145psi, Cylinder 5-140psi, Cylinder 6-135psi this test was done with the motor on the ground and powering up the starter motor. I dropped the sump and found broken oil squirters on cylinder 3,5 and 6. I was told my rings are probably worn so i stripped the motor completely to get a new set of rings for it. The trouble is no one has these rings anywhere and they have to be custom made by Ross over in the states and will cost about $600+$200 delivery. My question is how can i tell if my rings are at fault and if they are still ok and is this price ok for a set of rings?
×
×
  • Create New...