Jump to content
SAU Community

Recommended Posts

Hi guys, i'v got an r33gts-t and currently have the standard air box with no snorkle as the fmic pipe doesnt allow it to go on. I was looking into getting a pod filter and maybe have a cold air feed??? Whats the best thing to do and is there a certain filter i should go with?

Any help would be great!

Cheers James

Link to comment
https://www.sau.com.au/forums/topic/358090-cold-air-feed/
Share on other sites

I just have a pod filter inside of a custom aluminium box that I made with insulation padding on the inside of it.

On a forced induction car it aint a HUGE deal having no cold air intake if you have a decent front mount. Obviously it aint going to hurt though.

Link to comment
https://www.sau.com.au/forums/topic/358090-cold-air-feed/#findComment-5722153
Share on other sites

Do my intake setup IF you don't have a return flow cooler. Stock airbox (hacked up air feed to fit over cooler pipe. Put a hole in the bottom/side of the airbox. Put a duct from the airbox down through unused stock intercooler hole into front bar. Attach pod to the end of it. I have my guard liner in there too so cops can't see I have it so it's "legal" lol. Best way by far to do it. An you have 2 intakes :)

Link to comment
https://www.sau.com.au/forums/topic/358090-cold-air-feed/#findComment-5722484
Share on other sites

Do my intake setup IF you don't have a return flow cooler. Stock airbox (hacked up air feed to fit over cooler pipe. Put a hole in the bottom/side of the airbox. Put a duct from the airbox down through unused stock intercooler hole into front bar. Attach pod to the end of it. I have my guard liner in there too so cops can't see I have it so it's "legal" lol. Best way by far to do it. An you have 2 intakes :)

hehehe.i like this :)

Link to comment
https://www.sau.com.au/forums/topic/358090-cold-air-feed/#findComment-5723111
Share on other sites

Do my intake setup IF you don't have a return flow cooler. Stock airbox (hacked up air feed to fit over cooler pipe. Put a hole in the bottom/side of the airbox. Put a duct from the airbox down through unused stock intercooler hole into front bar. Attach pod to the end of it. I have my guard liner in there too so cops can't see I have it so it's "legal" lol. Best way by far to do it. An you have 2 intakes :)

hey mate, which part of the bottom side of the air box did you cut out? Can you draw a rough pic or take a pic of your air box for us?Cheers

Link to comment
https://www.sau.com.au/forums/topic/358090-cold-air-feed/#findComment-5723543
Share on other sites

hey mate, which part of the bottom side of the air box did you cut out? Can you draw a rough pic or take a pic of your air box for us?Cheers

I can try take pics mate. But it's in the car in a way that you can't tell it's there. I'll take a pic from the inside of the airbox and post it up tonight/tomorrow

Link to comment
https://www.sau.com.au/forums/topic/358090-cold-air-feed/#findComment-5723844
Share on other sites

Do my intake setup IF you don't have a return flow cooler. Stock airbox (hacked up air feed to fit over cooler pipe. Put a hole in the bottom/side of the airbox. Put a duct from the airbox down through unused stock intercooler hole into front bar. Attach pod to the end of it. I have my guard liner in there too so cops can't see I have it so it's "legal" lol. Best way by far to do it. An you have 2 intakes :)

Just did this mod to my stock air box today. Pretty happy with it.Cheers

Link to comment
https://www.sau.com.au/forums/topic/358090-cold-air-feed/#findComment-5725527
Share on other sites

save all the hassles with a 2 inlet mod restrictions and cut the snorkle around your intercooler pipe. at least you wont get any heat soke with a pod...

I just marked out the snorkle ovel the pipe and used a jigsaw then glued on some "Bunnings house flashing" (like soft alluminum)..

pic below. very easy and near stock....

mind you i did have to reglue it at the rear as I was impatient and installed it while wet...fixed now though

Regards,

dazza

post-65596-0-85377400-1300797197_thumb.jpg

post-65596-0-75903600-1300797210_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/358090-cold-air-feed/#findComment-5726157
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
    • Does it also misfire equally when revving?   Josh is very correct in what you should do. The coilpack harness wiring loom itself is a known problem due to its age and the number of heat cycles it has gone through. Throwing parts at a vehicle to diagnose the issue isn't a smart or good way to do it. Secondly, you may have a bad coil pack, you pop replacements in, they fix that issue, but messing with the harness breaks it, so the issue persists. So now you think "well it wasn't the coil packs" and have to continue chasing your tail, potentially swapping back in your shit coil packs and returning the good ones (yes, I've seen people do this because 'it wasn't the problem' and they want to save money). And suddenly, you've got two issues with the same symptoms...   Diagnose, don't use the spare parts shotgun.
×
×
  • Create New...