Jump to content
SAU Community

Recommended Posts

  • Replies 155
  • Created
  • Last Reply

Top Posters In This Topic

Exact same as R32.

Universal sensor, but the plug is same as R32.

If the plug isn't a direct fit, then the middle wire is signal, and the 2 outer wires are 12v for heating the sensor when cold (which you don't really need).

As long as your loom is from a DE, DET or 25DE the plug should be direct fit.

20E only uses a single wire sensor.

http://www.kudosmotorsports.com/catalog/ngk-ntk-lambda-sensor-oxygen-ntk-nissan-skyline-r32-gtst-gts4-gts25-rb20de-rb20det-rb25de-p-42.html

  • 5 weeks later...
  • 3 weeks later...
  • 1 month later...

Hey guys

nearing the end of finally getting my laurel finished and on the road, just wondering what i can use for a window washer bottle if i cant find a laurel one? and my windscreen wiper motor brother its little plastic ball joint, are all nissan ones universal?

And same with overflow or should i just get any random nissan overflow and make a bracket to hold it?

  • 2 weeks later...

hey guys im new on this site and recently bought a rb20det ceff anyway long story short i have come to the conclusion that my igniter pack(part number:2202058s01) (black box that sits on rockercover) has shat itself. is there anyother igniters that will work on this car (not phased about having to change plugs thats no issue and if so possible places i can find them? thanks guys

Cefiros come with both series 1 and 2 RB20s.

The square shaped plug on the ignitor module is series 1, series 2 has a same sized plug but the shape is a bit more round on the corners.

Hit any local Jap parts wrecker and they'll be able to sort you out.

Generally, S1 RB20s are found in R31s, S2 in R32s.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
    • Neg, the top one is actually for the front. The sizes are 18x10.5 +18 and 18x11 +32.   I measured many times but I'm sure I'll have problems as this is the thread for problems.
    • Just one thing; tapping tapered threads is tricky. Taps are always tapered and you would generally run it as far as you can, but with a tapered thread you have to stop much sooner otherwise the wide part of the taper will run in too far and you will have to thread the sensor in too far too as well (possible that it will never make a good seal) BTW nice wide wheels, I guess the top one is for the back!
    • Welp, good to know. Will have to wait awhile until steady hands with drills and taps are available. In other news, these just arrived! I will weigh them for posterity. Edit: 11kg each (or 10.9/11.1 depending on what my scale decides over multiple tests, the 18x11 don't seem to weigh noticeably any more than 10.5)  
×
×
  • Create New...