Jump to content
SAU Community

Recommended Posts

i looked in the engine bay and everything looks fine iv started the car im not sure if it was just laying around wit bits and pieces of the car of its vital to the car

its funny coz i just got the car last week and wen doing a service on it i have found parts just sitting in the engine bay eg turbo gasket

That's your AACV....car ain't going to idle or run without it....it should be mounted properly and hoses clamped on tight....very hard to beleive it just fell out.

Hopefully it was just another spare part laying around in the engine bay....

It mounts on your intake plenum around cylinders four and five, just below the throttle body.

Edited by Nic_A31

That's your Air Reg.(cold start fast idle valve)

Car will run fine without it PROVIDED the air hoses are re-connected properly.

Otherwise you'll have a huge air leak and she won't go.

My guess is it's been by-passed previously (aftermarket plenum perhaps) and finally decided to fall off.

It could be blocked off in the past and hence not affecting the engine. If that "were" to fall out, you'll have massive misfires, idle problems as it loops into the plenum.

Those usually fail all the time on RB20DETs and mechanics just block them off.

[quote name=ClutchBurndout-:(' timestamp='1300758954' post='5724847]

wait stop everything

u can block them off?

Correct, that's what mechanics so. Problem is sometimes on very cold days you might find you will need to slightly press down the accelerator to get the car to start.

The hose comes off the cross over pipe, into the AAC and back up into the plenum/TB. I've found out on several RB20s (including my previous car) that it was blocked off with a bolt.

Problem is when these AAC fail, no matter what you do, the idle is quite high. People often mistaken this for the IAC valve, spend hours adjusting idle, etc.

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...