Jump to content
SAU Community

Recommended Posts

  • Replies 804
  • Created
  • Last Reply

Top Posters In This Topic

yes you would.

When i put a gen GTR bar on my 32 sedan, i used the R reo (cause i was told i needed to, and the bar i bought came with it)

The only thing you'll notice when putting a genuine R bar on is that the sides buldge out a bit, due to the gtst being not as wide as the R.

Hope that helps. (someone correct me if i'm wrong.

depends who you ask! some say yes and some say no, try thegtr bar on the gts-t reo before you buy

I dunno about that lol, I see masses of R32's everyday gettin around my area. Very close to the same amount of 33's I see. They are all common but I still think 34's are the least common, especially coupes. Do see a fair few 34 sedans.

must be an area thing, naff all 32s in midland ,altho there is a nice n tidy 32 sedan up the road on great northern hwy

finally finished my repairs from the hail storm.... personally i think it's looking even better than before it got all dented.

thats f**king hawwt dude, rims suit it so well. always loved black 32s, but gunmetal has to suffice lol

Pulled the fans and intercooler/piping off yesterday. Degreased + highpressured the piping/cooler and the engine bay then cleaned the cooler core out with some thinners.

This afternoon the cooler/piping and fans will go back on and probably trim the front bar and bolt that up too.

Radiator was ordered yesterday :banana:

Clutch was inspected and deemed to need an overhaul kit.. ~$650 for the kit but not available until next month!! So looks like I'm going to grab a new Exedy button clutch instead.

Ordered my tensioners and idler this morning from Statewide Bearings, NSK part numbers, VERY reasonable prices!

The only unknown at the moment is injectors... anyone got some GTR injectors for about $100?:P

Fans back on, cooler on and plumbed up.

HID's wired but only one fitted because my drill went flat fkn (typing this while I wait for it to charge)... what a cnt of a job, the retainers in the wagon would have been perfect but the retainers in the 32 required some "modification".

Bonnet latch & support back on and operating well.

Need to pull the reo off and give it a bit of a grind tomorrow, the dodgy hacking from the previous owner fouls the cooler in one spot :(

Oh and a successful NIStune fitting today on a 34GTT, drive in drive out :D

Ok lets see if this drill has enough charge fkn

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • If it (the code) wasn't still current, it should have gone away by itself by now. No, nothing it 10/10. But it is quite likely. Everything else to do with the ignition could still be responsible (which is wires and connectors). The car is an old piece of shit now, so all the wires and connectors are also old pieces of shit.
    • Lock me in mate, although I'm not sure if I'll be heading up from Goulburn or down from Sydney, either way, return will be back to Goulburn 
    • Sounds good, we will aim to be there! @The Bogan I'll give you a shout if you are heading up to campbelltown for the meet too.
    • Before I get to the test day, just to finish off the android head unit. This is a demo from car start up....the standard/host system takes a few seconds to boot (same as all v37) but Android comes up quickly. In this vid I'm using the delivered launcher but have set the default to Agami since which is easier to navigate when if use primarily 5 apps. You can see the host system still takes over when required eg putting it in reverse, and you can switch between Android and not by holding the back button 3 sec. It is pretty responsive (fast) but you can see I had to press harder than expected a couple of times.  I still have the phone connected to the stock system, and that also seamlessly takes over Android music playing. v37-android-demo.mp4 The bigger reason that I put this in though is so that I can use Ecutek directly on the head unit. That gives me a dash with logging (up to 20MB only), high and low value warnings on any parameter etc etc. I've run a USB cable from the Ecutek OBD dongle to a USB input on the unit, easy. v37-ecutek-demo.mp4   The unit did freeze on the launcher the other day, I think Agami was trying to verify the license when it didn't have a data connection...will monitor and report back if there are any other problems but so far I'm very happy with the upgrade.
    • Nah that is just crappy GPS mapping, I did have a small excursion (cold tyres, damp track, surprise!), will post up that when I get a chance.
×
×
  • Create New...