Jump to content
SAU Community

Recommended Posts

Hasn't accepted yet.... :( Frowny face

oy, i will add you :P

[email protected]

thought i was camera proof until i gunned it through an orange on the westlnk the other night and 'flash-flash' ...going to have to research those ghost plates, pretty sure it was the speed not the red light.

Link to comment
https://www.sau.com.au/forums/topic/358645-bang/page/4/#findComment-5734178
Share on other sites

  • Replies 68
  • Created
  • Last Reply

Top Posters In This Topic

Unless your speedo starts eating the gear drive, you don't need to calibrate them, this is why they have to be between 0 and 10% over read at any time for any configuration of tyre approved by the manufacturer.

Most cars over read by at least 3% on brand new tyres. Oh and new to worn out tyres will alter reading by approx 0.5%...

That doesn't help Import drivers or older cars.

Link to comment
https://www.sau.com.au/forums/topic/358645-bang/page/4/#findComment-5736920
Share on other sites

That doesn't help Import drivers or older cars.

Perhaps not, but if a speedo becomes more inaccurate over time shouldn't recalibration be part of routine maintainance? I guess it's much like adjusdting headlights, something very important that everyone overlooks as it isn't regulated.

At the end of the day, it's up to the road user to obey the rules. If you get caught breaking those rules and your only excuse is "lol, soz my speedo is out" it is very likely you will end up with a speeding fine AND a defect ;)

Link to comment
https://www.sau.com.au/forums/topic/358645-bang/page/4/#findComment-5736947
Share on other sites

SMH states that the ADRs specify a 10% margin for error either way, yet the actual ADRs say that the margin for error only applies that the car is always going equal to or less than the speed displayed on the speedo...

I wonder what else in that article is incorrect?

TL;DR - Sensationalist journalism

Because the ADR changed in 2006 - and ADRs aren't retrospective. So vehicles produced before 2006 happily comply with the old ADR and the new ADR does not apply to them.

The old pre-2006 ADR stated (loosely) +-10% accuracy at speeds above 40kph (I beleive), the new ADR changes that. However, how many cars are on the road that were build pre-2006? The new rules essentially disallow under-reading, and permit over-reading by up to 4kmh + 10% (there's a formula involved, I believe someone has already posted this).

The other thing to consider is all the other factors that will impact speedometer readings -

+ tyre wear

+ tyre pressure

+ vehicle load

And that ignores more human factors like many speedos only displaying increments of 5kph, or particularly sized/shaped speedometer needles.

Unfortunately, the politicians really don't give a damn - it's all about revenue raising, not facts or 'real world'.

Link to comment
https://www.sau.com.au/forums/topic/358645-bang/page/4/#findComment-5737147
Share on other sites

It'll be interesting see if as a consequence of <1km/hr tolerance, the stats of rear-enders goes up.

And they probably don't do a count of those anyway.

Rear-enders are probably already on the rise - not just from wet roads which has always been the case, but from texting.

Link to comment
https://www.sau.com.au/forums/topic/358645-bang/page/4/#findComment-5737202
Share on other sites

It'll be interesting see if as a consequence of <1km/hr tolerance, the stats of rear-enders goes up.

And they probably don't do a count of those anyway.

Rear-enders are probably already on the rise - not just from wet roads which has always been the case, but from texting.

Funny you mention this...

P Platers have the STRICTEST laws in regards to speeding on them... Yet they're the lowest cause of rear end accidents... So by that fact alone, it should technically reduce...

Link to comment
https://www.sau.com.au/forums/topic/358645-bang/page/4/#findComment-5737367
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • all brand new unit from Tomei, fluid, bearings, etc. Tomei said they call it a 1.5 lsd because its 100 percent lock up under acceleration and 50 percent under deacceleration.  as I mentioned I used their fluid, install and their break-in procedure, (alot of figure 8's) but even when driving straight, or even slowly backing out of garage for first time, (at 2 mph) then driving to and from figure 8 parking lot, each tire in the rear would sporadically grab, skip, bounce, shutter and skip, shutter back a force I could feel causing clutch to slip then grab, at any speed. shaking entire car. I removed unit, since I put stock back in and all is fine, via process of elimination, its something with the lsd unit itself. I wasn't going to beat up the entire car more or change anything else for no reason as I had a feeling something in the lsd itself was wrong as everything was fine before this alone was installed and I rechecked over everything else after first time backing out I suspected an issue. I'll probably sadly already need new tires now just from trying to drive it 5 miles and performing the figure 8 break in. but if someone has any ideas I'm all ears 
    • Ok thanks..that was my second question if i can somehow bypass this even with Nistune(that is all i have right now...aparat from stock ECU. So with some aftemarket it can by "bypassed" or make it work?  I know there is Link or Haltech (mainly used). We have ECUmaster here so i will gather some info about it.
    • Yes. You will need to get the original boost sensor and wire it in. That is.... if you plan to use a stock ECU - even a Nistuned ECU. The Nissan ECU will not operate correctly without it connected. And yes, it will do annoying stuff like you are experiencing. You will almost certainly be better off with some aftermarket ECU, than trying to hunt down rare sensors.
×
×
  • Create New...