Jump to content
SAU Community

Recommended Posts

looking at upgrading my injecotrs and fuel pump b4 i get a tune and needing advice

in tank vs external which better? walbro vs bosch? looking for something that will fit in relatively easy without paying 3+ times the price to get a nismo one that will drop straight in.

what size injectors needed?

looking for 300awkw max but prob for better fuel ecomony and reliability will go closer to 250awkw.

300rwkw you might find will be OK with stock injectors. Some cars are, some aren't so as Jez said - just go with a fuel pump for now mate.

If you need them, get them. Otherwise you can tune to 280/290rwkw and save $700-$900 (purchase/fitting).

What turbos do you have? 300rwkw means non factory so you could probably make more if you did get injectors, you will need AFM's though.

not really keen on spending $600 on nismo pump which is more than 3 times price of bosch or walbro pump just coz its bit easier to install. from sounds of it unless i find a cheap set of injectors stick to what i got coz from what i can see like $600 sard 550cc injectors though the price to go to 1000cc injectors isnt much more.

so for fuel pump in tank vs external which better? walbro vs bosch? looking for something that will fit in relatively easy without paying 3+ times the price to get a nismo one that will drop straight in.

i got the N1 turbos, i tired searching several different topics nothing seems to come up but i get this alot guessing im just not using right words.

I have tuned a gtr 312kw stock injectors but a fuel reg.

250 kw is nothing for stock inj. Just get a fuel pump

What base pressure and afr bro?

But yea 250awkw is poossible with stock 444cc inj, even a little more......I'm doin roughly that now with them at 88% duty with 11.0 afrs,,,,and i'm sure your tuner wouldnt go that rich

Oooh ....an a walbro pump too....not in a gtr tho so i'm not sure about fitment

What base pressure and afr bro?

But yea 250awkw is poossible with stock 444cc inj, even a little more......I'm doin roughly that now with them at 88% duty with 11.0 afrs,,,,and i'm sure your tuner wouldnt go that rich

Oooh ....an a walbro pump too....not in a gtr tho so i'm not sure about fitment

I tuned it at 11.5 afr. I never set the base pressure myself so i can answer that one sorry.

Inj hit 105%

There is a new fuel pump, just released not long ago. It flows nearly 350lph at 45psi. 290lph @60psi all at 13.5v.

Basically it flows just over 30% more then a failbro 255, denso etc.@ 13.5v. As another comparison

the walbro and denso need 16.5v to run close to this pump at its 13.5v flow on 0.7 SG.

Nismo quotes 276lph @ 3 Bar pressure, no SG or voltage quoted

The only downside I can see is that it will probably surge on under 1/4 tank on a bnr32- more of a design prob of the

tank then pump.

Its a 100% drop in, in tank pump and the best part is, cost is about $250

I will be getting mine in a few days and post findings

What brand? Anyone needing more than 255LPH is going to be aiming for serious power and won't care about a couple hundred $$ saved, and will probably NOT skimp on it given how much was spent on the engine.

But, see how it goes :)

There is a new fuel pump, just released not long ago. It flows nearly 350lph at 45psi. 290lph @60psi all at 13.5v.

Basically it flows just over 30% more then a failbro 255, denso etc.@ 13.5v. As another comparison

the walbro and denso need 16.5v to run close to this pump at its 13.5v flow on 0.7 SG.

Nismo quotes 276lph @ 3 Bar pressure, no SG or voltage quoted

The only downside I can see is that it will probably surge on under 1/4 tank on a bnr32- more of a design prob of the

tank then pump.

Its a 100% drop in, in tank pump and the best part is, cost is about $250

I will be getting mine in a few days and post findings

would like more info on this pump and also you findings

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
    • Well they got my money but they are not getting my gearbox ! 
    • It's needed for rolling idle up, and I think it is a decider on VCT also.
    • I mean, not really. Link ECU's can absolutely still have errors from the ECU thinking it's getting a sensor it's not expecting. I would imagine the speed at the ECU level in Nistune does absolutely nothing anyway? I assume the ECU does not do any fancy TC stuff with regards to front+rear wheel speed or anything of that like anyway. Someone who uses Nistune may be more fluent in it. 
×
×
  • Create New...