Jump to content
SAU Community

Recommended Posts

hey all!

just a quick question !

i got this 12"sub http://mobile.jlaudio.com/products_subs.php?series_id=16 (on the left colum) and i am just wondering if this amp would be powerful enough http://www.lifestylestore.com.au/products/car/Sony/2-Channel-Amplifiers/XMZR602/ or should i get some more powerful ? im just looking to wire up my sub and my front speaker.

if anyone have any advice of amps please help me out. or if you have one for sale would b goood too.

(looking at around $100 to $200)

thank you!

Link to comment
https://www.sau.com.au/forums/topic/362884-sub-and-amp/
Share on other sites

i am no expert so someone can confirm my limited knowledge but i thought u would need a 4 channel amp to run the subs and the front speakers, unless the front speakers are run off the head deck, then this might be ok to power the sub. someone who knows there stuff should be able to confirm

Link to comment
https://www.sau.com.au/forums/topic/362884-sub-and-amp/#findComment-5791103
Share on other sites

more power then that, you would be disapointed and sony isn't my first choice in amps or even in top 20 choices

the sub needs about 300watts RMS but more is better then less. to a point that is,and get a proper box for it. not generic if possible.

a 2 channel amp like this can run the whole car with the right passive crossovers installed. and proper ohm loads but the power is meager at best.

hate to say it but import a amp from usa is a huge cost saver right now. even with shipping. just select a good one cause the warranty will most likely be void here.

I'd look for something name brand , 4 channel, 150 a channel at 4 ohms , you can do a ton of ways to set it up depending on what your goals are and how loud you want it. ?

Edited by sapphiregraphics
Link to comment
https://www.sau.com.au/forums/topic/362884-sub-and-amp/#findComment-5791170
Share on other sites

sony is crap. IMO get a 4 channel; 2 for your fronts (hopefully splits) and bridge the other 2 channels for the sub. Option audio make a good budget amp (that I have used) if you are going to buy locally.

Edited by sonnyQ
Link to comment
https://www.sau.com.au/forums/topic/362884-sub-and-amp/#findComment-5791459
Share on other sites

option audio is good, they're made by a chinese firm, and rebranded you would be shocked to see how many brands are the same amps.

when you run amps mixed mode, the passive crossover uses up some of the power. not much but some.and the cost of a coil or two for a sub exceeds the savings on the amps

splits in the doors, tweeeter near the mid for staging

amps I'd sugguest depending on budget and where you buy, (50-150watts per channel max)4 channel amp with active crossover (most have that built in ) run the fronts off the amp, bridge the rear channels to feed to the sub

somewhere in the 200-300 watts of clean max power should push it good even up to 500 watts max/peak but then you might void your warranty on the sub. the box needs to be right. the voltage needs to stay above 12v

the signal can't be distorted a lot and it won't play all day long at max volume, or kiss it good bye from a burnt voice coil

in no certain order

Rockford Fosgate

Orion

Kicker

Option Audio

lanzar opti or pro

MTX

earthquake

JL - same guts as MB quart on lower models.

Percision Power- no sedona series

Soundstream

Directed

Hifonics

Alpine

US Audio old stuff, blue , purple, red models. often on ebay cheap. these have guts from a major SPL brand in them

Jaycar , often overlooked but same guts/heatsink as option audio on older models, 1st place winner in major car mag. saw one on clearance just the other day for your price range.

Pionneer- upper models

Kenwood -upper models

Clarion - give chris rogers a call for those

Boss audio , mid models and up are cheap and ok for some basic installs

heaps more

but I'd be wrong pointing you to websites that sell these cheap, transshippers can create problems for local biz in USA and OZ and voids warranties etc.

call around, and find a decent installer.

don't forget your wiring will cost around 40 bucks in kit form min.

Link to comment
https://www.sau.com.au/forums/topic/362884-sub-and-amp/#findComment-5791637
Share on other sites

+1 for jaycar, had an old response amp in my VL and it pumped. And it was only a couple hundred brand new from memory.

Personally I would buy locally if dabbling in this entry level gear, for the peace of mind of warranty. Assuming the warranties are worth the paper they are printed on!

Link to comment
https://www.sau.com.au/forums/topic/362884-sub-and-amp/#findComment-5792078
Share on other sites

troy,

I also do RF. have plenty of that in my own drive car.

a 4ch amplifier would do nicely for the task at ahand. a RF 400.4 will do VERY well.

if thats a bit expensive for your taste grab a clarion one. quite a bit cheaper and still has decent power.

not a fan of option - found that in comparison against the other two they seem to have less output.

Link to comment
https://www.sau.com.au/forums/topic/362884-sub-and-amp/#findComment-5792895
Share on other sites

  • 2 weeks later...

Now usually I'd pay out on sony too but the other day I was given the opportunity to try their xm1s monoblock. It's a tiny 500w rms class d. I connected it to my type r and was reaaly impressed with the sound. I was runnung my sub at 2ohms and it pumped hard. But the best thing is that it practicaly didn't heat up at all. I ended up getting it in the end. Sorry if that was a bit off topic...

Link to comment
https://www.sau.com.au/forums/topic/362884-sub-and-amp/#findComment-5809459
Share on other sites

hi bro one amp that people do not think about is the audio line amps now i know that they are shit as for 2 and 4 channel amps but with the mono amps that you have they are great you can get a 800.1 for $189 from jb and they are quite good for the money. i work for them and we have tested it against all kinds of amps and its mad for the money.

Link to comment
https://www.sau.com.au/forums/topic/362884-sub-and-amp/#findComment-5811260
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...