Jump to content
SAU Community

Deca Officials

RCHOO

By RCHOO,
in Archived Events

 Share

Recommended Posts

RCHOO Grand Master

RCHOO

Posted
Posted

ITS DECA TIME

Saturday 4th June

And at this time we once again ask for your assistance.

For this event to run SMOOTH on TIME and SAFELY we need a small group of volunteers ( Officials )

to help out in 3 sections in the morning and 1 section in the afternoon.

And your assistance would be much appreciated.

All Officials on the day will be supplied with lunch and drinks.

A Officials briefing will be held before the drivers briefing so all Officials will need to be at

the Shepparton DECA Complex at 8.00am on the Saturday.

So if your thinking about coming up for a look and not competing this is a great way to get up close

to the action. And you will get a chance to do some passenger runs on the skidpan in the afternoon ( trust me ).

So if this sounds like you post up in here or send me a pm and i will put your name down.

Cheers WayneO. :thumbsup:

MORNING

Long Wang

STARTER.....Bec

TIMER .....Clive

FINISHER....Juliette

SPOTTER 1...Andrew

SPOTTER 2...

Mini Wang

STARTER.....Anna

TIMER.......Tim

FINISHER....Johnny

Skidpan

STARTER..... Wayne

TIMER....... John

FINISHER.... Matt

AFTERNOON

Skidpan

30min ON and 30min OFF for this session.. :thanks:

STARTER.....Wayne

TIMER 1.....Clive

TIMER 2.....Anna

FINISHER 1..Tim

FINISHER 2..Johnny

Link to comment
https://www.sau.com.au/forums/topic/363014-deca-officials/
Share on other sites
NUTWGN Proficient

NUTWGN

Posted
Posted

Lol I was going to say yup put me somewhere but you read my mind :)

I'll also do something in the arvo. No rush to head off this time - but I want to have a ride in the NUTR in the arvo session- just one, so will need someone to replace me for that minute or so...

Link to comment
https://www.sau.com.au/forums/topic/363014-deca-officials/#findComment-5793547
Share on other sites
NUTWGN Proficient

NUTWGN

Posted
Posted

is it possible to compete and help out or it's not really feasible?

In the morning not really feasible as you are split into two groups, and we run the wangs out the back then the pan in the front area so everyone is competing at the same time in different areas. Arvo it is one big group and only on the skid pan so if you are willing it would be greatly appreciated for you to rotate through if needed, we usually fall short in the arvo session.

Link to comment
https://www.sau.com.au/forums/topic/363014-deca-officials/#findComment-5800636
Share on other sites
Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • turbo76lx
      Torana Lx Gtr Hatch, Lots Of Pictures

      By turbo76lx · Posted

      Also build this EH ute with 370z motor and gearbox with a couple of turbos just for fun.  
    • turbo76lx
      Torana Lx Gtr Hatch, Lots Of Pictures

      By turbo76lx · Posted

      Got the passenger door on plus the master cylinder and booster. Loaded up to take it home. At home, the colour changes a lot in the light.
    • joshuaho96
      Jacks that fit under GTR lips that can reach the subframe?

      By joshuaho96 · Posted

      Nothing cheap, but I have seen the AC Hydraulic DK13HLQ which is pretty close to what you're asking for. The problem is the hydraulic cylinder mandates that the back of the jack be a certain height and Skylines have fairly deep inset floor jack points. A more certain and cheap option is to get some nominal 2x10 inch lumber boards and have one board be 1.5 feet, the other board 3 feet. Glue it all together with lots of clamps to maintain pressure. Make two of these. The ramp suggested above is a good idea, it takes quite a bit of clutch slip to get over each of the boards. I only need the first ~1.5 inches for my low profile jack on a standard ride height car but a lowered car you want to go up to the full ~3-3.5 inches. Paint it or store indoors if you want it to last.
    • Kapr
      Boost cut after swap(RB25DET NEO) R34

      By Kapr · Posted

      Ok. And Nistune? I read (here too) mainly on Stagea threads that it can by "turn off" with Nistune. But they say they still had the sensor plug in. Next week iam going to the Nistune(and other ECUs) tuner so i can finally make it work. I drove the car home and apart from the cut it drove great. No misfire no smoke no hesitation or rough start...so hoping it is this sensor that is missing  
    • GTSBoy
      Jacks that fit under GTR lips that can reach the subframe?

      By GTSBoy · Posted

      I just stack 2 pieces of 200x50 timber on top of each other. Total length about 900mm, with the top one being a little shorter and both having a 45° angle cut on them to make the front edge a bit of a ramp. Put these in front of each front wheel, drive up on them, throw the trolley jack under. Takes 1 minute. Scissor jacks can eat a bowl of dicks. I never use on under my car unless desperate.
×
×
  • Create New...