Jump to content
SAU Community

Deca Officials

RCHOO

By RCHOO,
in Archived Events

 Share

Recommended Posts

RCHOO Grand Master

RCHOO

Posted
Posted

ITS DECA TIME

Saturday 4th June

And at this time we once again ask for your assistance.

For this event to run SMOOTH on TIME and SAFELY we need a small group of volunteers ( Officials )

to help out in 3 sections in the morning and 1 section in the afternoon.

And your assistance would be much appreciated.

All Officials on the day will be supplied with lunch and drinks.

A Officials briefing will be held before the drivers briefing so all Officials will need to be at

the Shepparton DECA Complex at 8.00am on the Saturday.

So if your thinking about coming up for a look and not competing this is a great way to get up close

to the action. And you will get a chance to do some passenger runs on the skidpan in the afternoon ( trust me ).

So if this sounds like you post up in here or send me a pm and i will put your name down.

Cheers WayneO. :thumbsup:

MORNING

Long Wang

STARTER.....Bec

TIMER .....Clive

FINISHER....Juliette

SPOTTER 1...Andrew

SPOTTER 2...

Mini Wang

STARTER.....Anna

TIMER.......Tim

FINISHER....Johnny

Skidpan

STARTER..... Wayne

TIMER....... John

FINISHER.... Matt

AFTERNOON

Skidpan

30min ON and 30min OFF for this session.. :thanks:

STARTER.....Wayne

TIMER 1.....Clive

TIMER 2.....Anna

FINISHER 1..Tim

FINISHER 2..Johnny

Link to comment
https://www.sau.com.au/forums/topic/363014-deca-officials/
Share on other sites
NUTWGN Proficient

NUTWGN

Posted
Posted

Lol I was going to say yup put me somewhere but you read my mind :)

I'll also do something in the arvo. No rush to head off this time - but I want to have a ride in the NUTR in the arvo session- just one, so will need someone to replace me for that minute or so...

Link to comment
https://www.sau.com.au/forums/topic/363014-deca-officials/#findComment-5793547
Share on other sites
NUTWGN Proficient

NUTWGN

Posted
Posted

is it possible to compete and help out or it's not really feasible?

In the morning not really feasible as you are split into two groups, and we run the wangs out the back then the pan in the front area so everyone is competing at the same time in different areas. Arvo it is one big group and only on the skid pan so if you are willing it would be greatly appreciated for you to rotate through if needed, we usually fall short in the arvo session.

Link to comment
https://www.sau.com.au/forums/topic/363014-deca-officials/#findComment-5800636
Share on other sites
Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Chris' Toyota Mark ii JZX110

      By GTSBoy · Posted

      I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • GTSBoy
      RB26DETT Sketchy boost mod?

      By GTSBoy · Posted

      Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
    • MBS206
      R32 update from 1990's spec.

      By MBS206 · Posted

      With ordering the belt, you're doing water pump and the idler and tensioner at the same time too yes?
    • joshuaho96
      RB26DETT Sketchy boost mod?

      By joshuaho96 · Posted

      This is just a dumb way of keeping the wastegate closed to make more boost. Undo it and either follow the factory setup or redo it properly. Manual boost controllers just use a spring preload to determine when to close in response to boost pressure so it no longer vents to atmosphere.
    • djr81
      R32 update from 1990's spec.

      By djr81 · Posted

      So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
×
×
  • Create New...