Jump to content
SAU Community

Recommended Posts

Thats not a very fair comment. Some people actually enjoy working on cars and helping people out. Not just out there to get rich.

U don't trust a person but u trust Ebay gaskets lol

haha

hmmm..i do see your point...the gasket was from nitto though. They sell good stuff, dont they?.

i didnt say dont do it, I said only do it if you trust the guy, Ive seen some horror stories of the guy at the pub that said he would do it on the cheap..mostly i was trying to convince him to do it himself cause he thought he could

Getting is out is not that hard, getting the water banjos back on is a royal PITA.

Without a doubt, that is the hardest part!

Took me at least an hour to get the first one back on!! Then about half an hour for the next, and the last 2 were easy.

ive got a 3" dump. but when you run a small highflow (21U) around the track for 3 months the manifold and exhaust housing on the turbz don't last.

Mine is leaking atm (near blowing the gasket to shit) and will only do 1-2 more track days before it all needs to come out again.

ive got a 3" dump. but when you run a small highflow (21U) around the track for 3 months the manifold and exhaust housing on the turbz don't last.

Mine is leaking atm (near blowing the gasket to shit) and will only do 1-2 more track days before it all needs to come out again.

wow that bad huh , cant upgrade to an OP6.

So you just have to pull it out and replace housing and manifold or just gaskets?

You must be doin quite a few trackdays then, im pushing more power through the same housing but it doesnt get flogged anywhere near as hard as yours, well not consistently anyway :P be interesting to see how it lasts I guess my ebay gasket will no doubt give up before anything else , at least I hope it does

Trent fixed her up for me last week too,, come round and have a drive if you like sometime its running great. 430nm at 3500rpm See what ya think ;)

Really?

I thought (hoped) half way through ...

But anyhow, everybody has a first time at everything and I will get there (eventually)

:)

you have all the easy but fiddly bits done. all you have left is the hard and fiddly bits with a side order of swearing to go. lol. don't worry, you'll get there

>_<

Yes, you are right .. now it is hard and fiddly.

(unsure which part of the work I like better)

I was meaning to remove the turbo yesterday, but had to buy 2 axle jacks first (poor excuse)

But I removed further piping and also prepared the turbo by undoing the locking clamps.

I remember when I first removed the cylinder head of my motorcycle, it took 4 hours.

After some practise I was able to remove it and put it back on in one hour :)

Cheers from London ..

Alright,

The Turbo is out ..

Worst bit:

The Water-Return-Pipe banjo bolt.

Also the turbo to manifold bolts gave me much less trouble than expected, thankfully I had an ultra slim ring-spanner

in my toolbox ... and it was even 17mm! :) The spanner did fit right over the nut, so I was lucky.

I did not remove the dump-pipe from the turbo, it was not a problem getting the turbo out.

(Just removed the 3 nuts from the downpipe to dump-pipe connection.)

Would I do this again?

Yes, but only in a proper garage ... not in an underground parking space.

More later ... many thanks for the help .. :)

post-33912-0-98452000-1305375640_thumb.jpg

post-33912-0-31695400-1305376795_thumb.jpg

post-33912-0-16382400-1305376805_thumb.jpg

Edited by Torques

nothing wrong within an underground carpark mate.

At least its out of the rain

This is my 'garage' and its been apart more than a few times before in it..

13032011409.jpg

This is actually an upgrade my last 'garage' was only half as big :D

Good point, yes .. I plugged every opening with a cloth ..

Especially the pipes to the inter-cooler which are now wide open .. don't want any clip ending there, and then being vacuumed

by the turbo ...

Becareful with the compressor outlet of the turbo or any other opening eg cooler piping etc. Cover them up with rags or similar, its very easy to drop something in them.

Haha ....

Yes, nothing wrong with it, but I got strange looks from fellow citizens ;)

I like your garage ... very airy and no prying looks!

Also close to the next fridge I suppose!

BTW:

Attached why I had to remove the turbo ..

nothing wrong within an underground carpark mate.

At least its out of the rain

This is my 'garage' and its been apart more than a few times before in it..

13032011409.jpg

This is actually an upgrade my last 'garage' was only half as big :D

post-33912-0-84894100-1305490470_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...