Jump to content
SAU Community

Recommended Posts

  • Replies 77
  • Created
  • Last Reply

Top Posters In This Topic

If you get back to me about the exhaust then i'll get back to you about your membership?

LOL

But you are a member mate. 2013 expiry. You paid me 3yrs last year @ RE :thumbsup:

Email Dan for a new card: secretary @ sauvic.com.au

If i wasn't out clubbing the night before - I'd be in for this :(

from their site:

Spectators are more than welcome, and there is no cost to come and watch. Also you can go for a ride in the cars but you must sign on with a Passenger indemnity first. Due to the amount of passengers at previous events our insurer has put a small levy on passengers of $20. You can just pay this when you sign the forms at the Scrutineering office.

So if u can talk some-one into a ride 20$ for some passenger laps!

Yeah $20 is steep for a couple of passenger laps.

Im in double entering the car with johnny again. Looking forward to it, hope it gets a bit above 15deg though!

When do we find out what groups we are in etc?

Edit: Ash you always have some excuse!

They run so many passengers during the day (all sessions are passenger) that insurance for the passengers is needed, thus the $20.

Don't expect an email from Adam again until 1-2 days before the event.

15deg is awesome, street tires love it. I remember setting a 39 with less power, suspension and braking mods than I have now on 235 KU36, 12 months ago in similar weather (colder, the guys that had towed up in the morning were scraping ice off the race car).

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...