Jump to content
SAU Community

Recommended Posts

  • Replies 105
  • Created
  • Last Reply

Top Posters In This Topic

While we are on the subject, I was after some info. My uncle owns light plane and CASA has informed me that I can't add this to the engine due to a couple of things, 1. It's not an approved addative nor a patented product and the chemical composition is not up to aeronautical standards yada yada yada?!?!? and 2. It reduces metal integrity by imbedding it’s self into the metal which on constant revving engines can cause a decrease in thermal efficiency. Sounds a bit ‘how ya going’ to me, didn't really get a straight answer from them, but do you know if any of this is correct? Thanks :)

An internal combustion engine is a great big oversize heat pump... it relies on heat not escaping in order to be most effecient. I'm also aware that Roil isn't for use in the general aviation industry... having been a pilot for the last 4 years, and studied aircraft systems at Griffith University (I'll quote you my CASA ARN and Licence Number and that of my licencing delagate if anyone thinks I'm BSing!) And i don't beleive Roil afffects 'metal integrity' when the pinion drive that powered the 2000 Australian national drag Champion 'Sainty' that ussually has be be replaced after every second run, and even then comes out with hairline cracks, once a new pinion drive had been socked in Roil for 24hrs at last count I beleive has done its 26th run???

1roil.1.gif

Note the rather large Roil sticker infront of the right wheel!

HoeTrain, the reason CASA wouldn’t recommend it is because they are a bunch of spineless, ball'les beurocrats who will not accept responsibility for anything. They wouldn’t even tell you the time without receiving written conformation from another source (just incase they were wrong). In all honest CASA know next to nothing about mechanicals (or aviation for that matter) and are just a lot of mindless beurocrats that hide under the comment "its in the interest of safety" (translation = "I don’t know and am not prepared to make a decision")

Sorry a bit of a rant, but when you have been involved in aviation (both flying and maintenance) a our family have, you have little respect for these pencil pushing dickless morons.

id like to see a proper test done by the manufacturers... like BMW and Mobil did with an old e30 with mobil 1 in it. they put it on rollers for 1million km's (might of been miles, i cant remember) and ran the engine non stop, and varied the speed periodically. they didnt change the oil at all and when theyd finished there was very little damage to the engine (similar to an engine thatd run 100,000ks using basic oil).

if a test like this was done (a before and after) there would be no variences like driving styles. and no one could argue that your full of shit (im not saying you are)

they wouldn't have to do a 1million km test of course.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hang on. Let me get this straight. The desire is to have coilovers, BC in particular, to be MORE comfortable on Sydney roads than stock suspension? Well, that's obviously not right. BCs have crude damping design at the very best, and typically hard spring rates. BC stands for Billy Cart. And then, the desire is to put in some shitty old worn out stockers, to get it blue slipped and then put the BCs back in? And then.....what? Not worry about getting pulled up by the Plod? Because you seem to have raised a worry about paying for engineering (which actually does solve all your legality problems) and still getting pulled up.... but the only problem there is that if/when that happens you have to show your paperwork at the inspection station. Whereas, if you just swap in borrowed shitty old stockers to get it slipped now, and then you get defected in the future, you have to go find more shitty old stockers then too. You course of action looks like this set of options: Buy brand new stock type dampers, and springs. probably cost a bit more than $1k all up, but will last for the remaining life of the car. Put them in, pass inspection, drive on them forever more. Hell, they could even be really nice Bilsteins and Kings or other lower&stiffer springs if you wanted. Get the car engineered as is. ~$1k. Buy new Shockworks coilvers (or MCA) and also pay for engineering. You're spending a lot more here. But these will be the best things that you could drive around on.
    • Might be worthwhile hitting up Facebook's groups, I know most of them contain terrible people and scammers - however you might be able to find someone that's in Sydney with factory suspension you could purchase and/or hire. Just do not send any form of money anywhere, in person cash only.
    • Thanks @Duncan Ride height is fine. I think it's almost stock tbh. Happy to share a pic. I don't actually have a regular mechanic as haven't lived in Sydney too long. Could you or anyone recommend any shops in Sydney?
    • You just need a different blue slip shop (preferably one you regularly use as a mechanic), and make sure the coil overs are as close as possible to standard height
    • yeah the sugar refining companies were pushing for the same in Oz originally, all fuels were going to have 10% ethanol to make them "cheaper" (noting, that the loss in l/100 might be greater than the decrease in price). I guess they won that fight in Canadia
×
×
  • Create New...