Jump to content
SAU Community

Recommended Posts

  • Replies 3.6k
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

sled nice taxi ull be amazed how agressive the little turbo on the xr series pulls they max out at 320ish but thats the most impressive rollons ever with a zf u did get a zf didnt u ? or u go stick :rolleyes:

one of the blokes had a ego one 320 on tolly did a 12.2 @119mph but on the street got car lenghts on any of us at 60km/h on wards weapon 4 sure :thumbsup:

On the dyno with stock ECU I'm assuming? I've never checked to be honest...

Needs a tune pretty bad, getting an absolutely horrible amount of k's out of it.

There's no tuning that you can do with a stock ECU. The only thing that you can do it adjust the base timing at the CAS and anyone can do that with a timing light. If your fuel mileage has become worse then i would be looking at your O2 sensor.

Sorry bud, here you go:

Specs to follow via a Dyno Sheet next week when it goes to Willalls so Martin can work his magic

Really looking forward to this SLED. There are a lot of new techniques in the tuning of these cars that arent being implemented in South Australia currently. I know this as none of the SA Tuners attend the Australia wide advanced Ford tuning workshops....and I am the headmaster :)

Your tune will have 'all the fruit'

On the dyno with stock ECU I'm assuming? I've never checked to be honest...

Needs a tune pretty bad, getting an absolutely horrible amount of k's out of it.

There's no tuning that you can do with a stock ECU. The only thing that you can do it adjust the base timing at the CAS and anyone can do that with a timing light. If your fuel mileage has become worse then i would be looking at your O2 sensor.

Also prob won't hurt if you changed the plugs and done a service at the same time, ie oil, coolant, filters, give your intake filters a good clean. That should get your car running just right :D

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
×
×
  • Create New...