Jump to content
SAU Community

Random Leaning @ Idle And Coasting

StealthX

By StealthX,
in Engines & Forced Induction

 Share

Recommended Posts

StealthX Veteran

StealthX

Posted
Posted

Hey guys.

My car was doing something strange yesterday.

It started going lean and popping at idle, at normal operating temp, so I grabbed out my hand controller and my LC1 was telling me it was running about 18-20AFR!

Everywhere else was fine, under boost, cruising above 2000rpm etc, all fine, but as soon as the revs dropped below 2000rpm, coasting with no throttle and idle conditions caused the pop. Coasting down in gear under 2000rpm made it pop like mad. It's as if anything below 3mS of fuel became unstable, like I was running 1000cc injectors lol

It usually takes about 2.0mS of injector to get 12-14AFR at idle depending on ambient temp, but yesterday I needed 20% more fuel, 2.4mS gave me 14-15AFR with the occasional pop and 16-17.

Does anyone know what this sounds like? Keep in mind I havn't changed anything before, all I've done was install some LED angel lights, which weren't even on at the time.

dying fuel pump - unlikely, the pump is only 18 months old

blocked fuel filter - possibly

dirty injectors - maybe

bad batch of fuel - maybe, I filled up at Gull using their 98, which I had never done before!

Any ideas?

Link to comment
https://www.sau.com.au/forums/topic/365739-random-leaning-idle-and-coasting/
Share on other sites
Lithium Grand Master

Lithium

Posted
Posted

Whats your setup - do you have an AFM?

What kind of voltage is the ECU reading?

Does the car do it consistantly since you first spotted this issue, or was it a once off?

And to clarify, do you mean specifically coasting down - or if it is actually sitting there at idle, will it stay at 18-20afr consistantly?

StealthX Veteran

StealthX

Posted
  • Author
Posted

Whats your setup - do you have an AFM?

What kind of voltage is the ECU reading?

Does the car do it consistantly since you first spotted this issue, or was it a once off?

And to clarify, do you mean specifically coasting down - or if it is actually sitting there at idle, will it stay at 18-20afr consistantly?

Sorry not much info... haha

EMS Stinger - map sensored, no TPS.

Engine is a QR25DE+T

returnless fuel system, walbro pump, 440cc WRX injectors, stock everything else.

I'm not sure if it's a one off, I havn't started the car up today, just been sitting here studying all day - ill report back when I go for a drive later.

There's two situations that it does it, at idle, and coasting down in gear at low revs, both occur at low throttle, below 2000rpm.

it's odd because it's never done this before!

Does it sound like anything common?

Rolls Grand Master

Rolls

Posted
Posted

I had this sample problem and couldn't fix it, would backfire badly when coming back onto the throttle and would pop at idle idling around 17:1 then would go back to 12:1

even had pete from nistune look at it and he wasn't sure of the cause

StealthX Veteran

StealthX

Posted
  • Author
Posted

I had this sample problem and couldn't fix it, would backfire badly when coming back onto the throttle and would pop at idle idling around 17:1 then would go back to 12:1

even had pete from nistune look at it and he wasn't sure of the cause

That's exactly what my car is doing!

Aside from the current leaning problem, my car has always had an issue at around 1700rpm, you have to apply load very smoothly, otherwise it'll buck down and die, I've tried adding up to 40% more fuel at these points and it does nothing. As long as the car's had the EMS there, its had a problem at 1700rpm, but now since this new tank of fuel, it's developed this weird leaning condition.

Actually thinking of it now, the servo that I filled up at was a United. Up until last week I've avoided them because I didn't know they sold 98. But last week I filled up with their "98" for the first time. I'm leaning (pardon the pun) towards bad fuel...

blind_elk Grand Master

blind_elk

Posted
Posted

Frankly, I wouldn't be worrying about running so lean at idle. It will not damage the engine at all, because there is virtually no load on the engine.

As for the popping, have to set up the EMS to shut off the injectors when the throttle closes (such as when you coast down, or change gears)?

StealthX Veteran

StealthX

Posted
  • Author
Posted

Doesn't have an idle map as such, it's got a separate function for idle control, then I've just tuned the points around idle for 12-14 ish, then air temp and water temp correction values take over from there too, none of which I had changed before it started going wierd. Has no TPS.

Dont know what fuel pressure is doing, I dont have a fuel pressure gauge, if it starts going wierd again I'll look into it further...

Went fir a drive yesterday and it's all fine again...

StealthX Veteran

StealthX

Posted
  • Author
Posted

Loose wires somewhere?

I cleaned up all the mess behind the head unit yesterday, coincidentally it stopped being wierd, but all I was doing was cable tieing things up, besides there's nothing behind there to alter fuel control...

Anyway thanks for your help bros!

StealthX Veteran

StealthX

Posted
  • Author
Posted

Okay so the problem surfaced again today, and today was the same type of day. It's got something to do with overcast humid days. Not necessarily hot vs. cold, cos it runs fine at night and during a hot day. Maybe humidity plays a part?

i'm gonna do a fuel filter, run some injector cleaner through and install an air temp sensor and tune some air temp comp maps, see what that does.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Watermouse
      Original window sticker?

      By Watermouse · Posted

      I got a full sheet set of OEM copied stickers to replace all the faded engine bay ones, great quality too.  Came from England. Someone like that should be able to to make u up what u want so long as u have a quality image to show them 🤷🏻‍♂️
    • myrbgivesmeheadaches
      RB25DET NEO Cylinder Head

      By myrbgivesmeheadaches · Posted

      Did this end up working? Did you take some pictures?
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      And finally, the front lower mount. It was doubly weird. Firstly, the lower mount is held in with a bracket that has 3 bolts (it also acts as the steering lock stop), and then a nut on the shock lower mount itself. So, remove the 3x 14mm head bolts , then the 17mm nut that holds the shock in. From there, you can't actually remove the shock from the lower mount bolt (took me a while to work that out....) Sadly I don't have a pic of the other side, but the swaybar mounts to the same bolt that holds the shock in. You need to push that swaybar mount/bolt back so the shock can be pulled out past the lower control arm.  In this pic you can see the bolt partly pushed back, but it had to go further than that to release the shock. Once the shock is out, putting the new one in is "reverse of disassembly". Put the top of the shock through at least one hole and put a nut on loosely to hold it in place. Put the lower end in place and push the swaybar mount / shock bolt back in place, then loosely attach the other 2 top nuts. Bolt the bracket back in place with the 14mm head bolts and finally put the nut onto the lower bolt. Done....you have new suspension on your v37!
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      And now to the front.  No pics of the 3 nuts holding the front struts on, they are easy to spot. Undo 2 and leave the closest one on loosely. Underneath we have to deal with the wiring again, but this time its worse because the plug is behind the guard liner. You'll have to decide how much of the guard liner to remove, I undid the lower liner's top, inside and lower clips, but didn't pull it full off the guard. Same issue undoing the plug as at the rear, you need to firmly push the release clip from below while equally firmly gripping the plug body and pulling it out of  the socket. I used my fancy electrical disconnect pliers to get in there There is also one clip for the wiring, unlike at the rear I could not get behind it so just had to lever it up and out.....not in great condition to re-use in future.
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      Onto the rear lower shock mount. It's worth starting with a decent degrease to remove 10+ years of road grime, and perhaps also spray a penetrating oil on the shock lower nut. Don't forget to include the shock wiring and plug in the clean.... Deal with the wiring first; you need to release 2 clips where the wiring goes into the bracket (use long nose pliers behind the bracket to compress the clip so you can reuse it), and the rubber mount slides out, then release the plug.  I found it very hard to unplug, from underneath you can compress the tab with a screwdriver or similar, and gently but firmly pull the plug out of the socket (regular pliers may help but don't put too much pressure on the plastic. The lower mount is straightforward, 17mm nut and you can pull the shock out. As I wasn't putting a standard shock back in, I gave the car side wiring socket a generous gob of dialectric grease to keep crap out in the future. Putting the new shock in is straightforward, feed it into at least 1 of the bolt holes at the top and reach around to put a nut on it to hold it up. Then put on the other 2 top nuts loosely and put the shock onto the lower mounting bolt (you may need to lift the hub a little if the new shock is shorter). Tighten the lower nut and 3 upper nuts and you are done. In my case the BC Racing shocks came assembled for the fronts, but the rears needed to re-use the factory strut tops. For that you need spring compressors to take the pressure off the top nut (they are compressed enough when the spring can move between the top and bottom spring seats. Then a 17mm ring spanner to undo the nut while using an 8mm open spanner to stop the shaft turning (or, if you are really lucky you might get it off with a rattle gun).
×
×
  • Create New...