Jump to content
SAU Community

D2 Coilovers For R32 Gtst

wlspn
 Share

Recommended Posts

wlspn Proficient

wlspn

Posted
Posted (edited)

As mentioned, have a full set of D2 coilovers for R32 GTST.

Brand new in box, only been looked at.

Bought these then found out I have a GTR rear-end in my car so no good to me at all.

Slightly later style (purple & black, not all purple) street spec.

Spring rates are 8kg front, 6kg rear, have base height & damper adjustment.

All tools, etc included.

Looking for $1000 ono pick-up

Located in SE Melbourne

Best reached by SMS on 0423 303 007

post-35893-0-63563400-1306830939_thumb.jpg

post-35893-0-79888900-1306830986_thumb.jpg

Edited by wlspn
Link to comment
https://www.sau.com.au/forums/topic/366239-d2-coilovers-for-r32-gtst/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Neil's R33 Gts-t Build

      By GTSBoy · Posted

      Starter motors used to use the weight of metal (magnets) to provide torque. Now they use (more) current instead. This. It's completely normal.
    • Duncan
      Neil's R33 Gts-t Build

      By Duncan · Posted

      So thing that had me stumped, but I think is OK....is that when it was up in the air, in neutral I had it running to bleed to coolant while I put the wheels back on. I noticed the rears were turning (slowly) which I'd never seen before 20250928_163512.mp4     Because there had been an issue with clutch slip due to pedal adjustment on the dyno, I assumed there was still and issue so spent some quality time upside down under the dash adjusting the pedal....but no matter what I did the wheels still turned in neutral. Even disconnected the master cylinder to pedal rod and same. In despair, I even removed the clutch slave so there was no chance of any preload causing it.....still happened. So either: 1. Something is not right in the bellhousing, or 2. Its a thing sometimes with cold, thick gearbox oil Internet says it might be 2, I hope so!
    • Duncan
      Neil's R33 Gts-t Build

      By Duncan · Posted

      OK, few more things sorted and it is ready for a shakedown on 10-Oct, with one weird thing. Changed the run in oil and filter for the good stuff. 8l came out, about 8.5 went in with filter so that looks all good. Changed the starter (again), this time for a brand new one, works good. Interesting that the Taaaarks one is shorter than factory but spins harder, I guess electronics have moved on a little in the last 30 years. Will be nice to have a bit of extra space under there. Put the timing cover back on, and noted where the cam gears were set as a record.  Will need to double check the timing but it is pretty close. Also put the coil pack cover and intake snorkel back on. Exhaust Inlet Changed the water out for coolant, bled up nicely. Removed the rear brake pads (well worn factory sumitomo ones!), gave the hardware a good clean and reassembled. I've put bendix XP on the back again because the price is excellent at $150 a set and they worked well on the V37. Front pads have plenty so no issue there
    • jez NF
      The Evolution Of "night Fury"

      By jez NF · Posted

    • r32-25t
      remote oil cooler hose size, 8,10 or an12?

      By r32-25t · Posted

      Mine is all -12, I’m running a dry sump in a billet block though 
×
×
  • Create New...