Jump to content
SAU Community

Recommended Posts

Mid semester break is approaching fast and I wasn't sure whether to post this here or in the general automotive section.

With 100,000kms coming up on the clock, the car is frequently getting the 'yellow check engine light' coming on, not always about one in every 10 trips and I notice nothing different about the car when it does pop on so I didn't get it checked out.

I want to go for a trip along the east side and was wondering what I need replaced and if the car would actually make it all the way there and back without blowing too many tyres and radiators etc.

This is what I had in mind for the trip:

Install a pod filter

Possibly install a cat-back exhaust (to make the engine breathe easier)

Replace timing belt

Get new tyres

Do the usual service things

Get the stock clutch checked?

Would this be sufficient to travel a few thousand KMs from Melbourne and back? Let's say I'm going to Brisbane / Sydney or maybe Adelaide.

My car is a naturally aspirated r34 skyline.

EDIT: THE CAR IS COMPLETELY 100% STOCK!

Any opinions or thoughts?

Please move this into the right section if this is in the wrong section, thanks mods!

Edited by Grey
Link to comment
https://www.sau.com.au/forums/topic/366793-along-the-east-coast/
Share on other sites

Exhaust and pod aren't going to do anything to help you. If anything (and I mean with negligible effects) they are both counter productive to engine longevity.

Just get a service, do some long trip checks and stop every few hundred km (piss/food stops) to give things a rest. You'll be sweet. Cars are built to drive for a long time!

so you don't think it will break down in the middle of no where or anything like that?

It's a car mate.

It's designed to be driven. You are no more likely to breakdown than anyone else.

Just get the 100k service done. That alone will cost you more than you are thinking TBH.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Oil change does not trigger code 21. Code 21 is for coilpacks primary side connection. You can try to clear the code with a battery disconnect, hold down the brake pedal to drain capacitors through the brake lights with the ignition on for 10-15 seconds before you reconnect the battery. I have seen R35 coil conversion permanently cause this code with no ill effects so it might be the resistance it wants to see isn't quite right on one or more coilpacks. Could be inside the ECU, could be the harness, could be a coil. You can test it all if you want or just ignore until the car actually starts misfiring.
    • I forgot you have a Nistune ECU. Use Nistune to do all the tests I mentioned instead of faffing with 30+ year old electrical connectors. You can read MAF volts off that too, there are reference values in the service manual to tell you roughly what it should be in different conditions.
    • No. I think it might be the AFM. Hence the use of the terms "swaptronics", which implies the use of swapping out electronics for the purpose of diagnosis. It's about the only way to prove that a small/niggling/whatever problem with an AFM or a CAS or similar is actually caused by that AFM/CAS/whatever. A known good item swapped in that still gives the same problem is likely to be caused somewhere else. They're all the same. Spraying AFMs with cleaner is an each way bet between cleaning it and f**king it.
    • Oh wow! This might actually work amazingly. Do you know the ratio of the diff? I was told the only thing you need to make sure of is if the front & rear diff ratios are the same. Ours is a 4.083 Thanks!
    • You think its the AFM? I know its a common issues on R32s. I find it coincidental how this issue raised right after cleaning the fuel system. As everything except the fuel system was fine before. I tried running it with the IACV unplugged but did not notice a difference and still stalled. However, the RPM gauge is not in the cluster right now, so I will need to connect the laptop again and use Nistune to check the RPM. I will check this weekend.
×
×
  • Create New...