Jump to content
SAU Community

M35 Dtc Code 1805

andy65b

By andy65b,
in Four Door Family & Wagoneers

 Share

Recommended Posts

  • Replies 101
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Posted Images

Jetwreck Grand Master

Jetwreck

Posted
Posted

dont have a switch yet.. and surely thats not good for the attessa system right??

and as i said, these tyre will JUST start to slip but wont spin at stall, they're still new and really soft and sticky.. sometimes i wish i had nankangs lol..

i reckon i'll get em spinning once i do the brakes, i wont have to stand on em as much

Nankangs or not it would still bag em!

Jetwreck Grand Master

Jetwreck

Posted
Posted

yeh in RWD..

OFF TOPIC.

im closer to fixing my wastegate issue.. then i can probably retune low end, and have better response..

f**king hate this "safe" tune. everythings all over the place.

so you mean your car wont be a dyno queen anymore :P

prince_skyline Community Regular

prince_skyline

Posted
Posted

There are many M35's getting around with the mod done now, none of the ones down here have the MIL up yet that I know of... Perhaps its just you Canadians? :nyaanyaa: Im sure they will pop up eventually. I fitted a switch in one today, just next to the ecu. If the light comes on he will just switch it back on for a minute. We need to come up with a simple switch/circuit to automatically enable the brake circuit for a single pulse. Perhaps a momentary switch on the brake or handbrake?

Thanks Scott - all good so far!!! will let you know when and if it throws a code....

andy65b Veteran

andy65b

Posted
  • Author
Posted

I was speaking to Spoolin12 today and his car threw the 0185 code one week after cutting the wire. It also limited boost to 0.7bar.

This explains why my car threw the 0235 code at the same time. I have a boost controller fitted and the ECU could not alter the boost so it threw a hissy fit.. lol

ironpaw Veteran

ironpaw

Posted
Posted

I was speaking to Spoolin12 today and his car threw the 0185 code one week after cutting the wire. It also limited boost to 0.7bar.

This explains why my car threw the 0235 code at the same time. I have a boost controller fitted and the ECU could not alter the boost so it threw a hissy fit.. lol

Not sure if mine ever threw a code due to CEL being on with EMU, but if the engine's retarding itself I sure as hell can't feel it...managed to break traction tonight LOL

scotty nm35 Grand Master

scotty nm35

Posted
Posted

Not sure if mine ever threw a code due to CEL being on with EMU, but if the engine's retarding itself I sure as hell can't feel it...managed to break traction tonight LOL

On gas? :blink:

Who would have thought... lol.

I don't think it will be a problem for those of us with the engine light up, and the boost solenoid missing in action. It seems to just lower the boost luckily.

andy65b Veteran

andy65b

Posted
  • Author
Posted

but if you take off the boost solenoid wont you get an engine light anyway? (mine was taken off after the emanage so im just assuming)

No error code if you do that... if you disconnected the boost sensor that would be a different story..

Dunc Mentor

Dunc

Posted
Posted

No error code if you do that... if you disconnected the boost sensor that would be a different story..

Really? Id have thought if you disconnected it then it'd notice/say something. Plumbing it back onto itself, however, causes no codes :whistling:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      New kid on the block

      By GTSBoy · Posted

      The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Duncan
      New kid on the block

      By Duncan · Posted

      Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Songo
      New kid on the block

      By Songo · Posted

      Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
    • iain_ST44GA
      M35 VQ25DET starter motor

      By iain_ST44GA · Posted

      Hi Guys, Does anyone know any aftermarket part numbers for a starter motor to suit the VQ25DET? I can find lots of alternative part number for the VQ35DE, which I assume would fit, but there is a lot of conflicting information out there. Thanks..
    • Murray_Calavera
      R33 GTR running -9 with no tune

      By Murray_Calavera · Posted

      I don't understand how this hasn't boiled down to - Upgrade the turbo when you have everything required. ECU, injectors, fuel pump, turbo, etc. Do it all at once.  If you don't have everything required, just enjoy the car as it is and keep saving up your pennies. 
×
×
  • Create New...