Jump to content
SAU Community

Recommended Posts

Big thread update for 2013

All prices are before postage, bigger items can be sent with courier. Items are located in Brisbane.

Sparco Pro 2000 seat, black in colour. Never been used other than trial fitting. Comes in original plastic and box. $700

Bride RH seat rail, suits R32.33.34GTR. Has N303 on its sticker. $250 Can do a deal with rail and seat together.

Apexi Power FC to suit S1 RB25 and wiring loom for RB25 into R32 conversion. No commander. (Tuned for 35R and 550cc injectors, 380whp) $800

Sard 550cc side feed injectors. Fitted to RB25 fuel rail. Ready to bolt in $500


Z32 80mm Airflow meter (with free Apexi air filter) $160 Cheap!

Trust/GReddy RB25 stainless manifold. $400

Trust/GReddy RB25 plenum throttle body adapter to suit standard throttle. $130

Oil Cooler kit from Old HEL group buy. Is missing the Setrab core. $300

Oil cooler core, 9 Row with dash ten fittings. Came from Trust oil cooler kit. Looks weathered/old. No leaks when removed. $50

(Could be used with above kit with adapters for smaller fittings).


R32 (GTST/GTR) Hicas lock bar with the rack ends and new genuine ball joints for the knuckle. $120


R32 Type M front bumper (white), in fair condition. Has had both corners repaired $100

Mesh from R32 GTR bumper. $10


Z32 5 spoke, 16x7.5" wheels (old tyres). $40 Cheaper than tyres!

Riverside Mesh wheels, 16x8 +1. No tyres $280

Set of 4 'Guigarro Design' 2 piece. 16X8, 16X8.5 (5x114.3) (exact offsets between +35 and +45). The offsets marked on the rim may be inaccurate).

Good condition, only two have centre caps. (The 8.5's will not fit on the back of a R32 gtst they foul where the hicas tie rod end attaches to the rear knuckle.

They also will not fit the front because the front calipers). $300

Wheel spacers to suit (Mazda, Toyota, Honda) m12x1.5 thread 20mm. $50

Sparco Bonnet pins, still in packet. $20 Cheap!

Pics of some items posted earlier in thread. New items pics on request. All prices have some negotiation. Contact by PM or SMS 0432227533. Thanks!

Edited by Kisuu_Buta
  • Replies 117
  • Created
  • Last Reply

Top Posters In This Topic

  • 2 weeks later...

All prices are before postage, bigger items can be sent with courier. Items are located in Brisbane.

Sparco Pro 2000 seat, black in colour. Never been used other than trial fitting. Comes in original plastic and box. $650

Bride RH seat rail, suits R32.33.34GTR. Has N303 on its sticker. $200 Can do a deal with rail and seat together.

Apexi Power FC to suit S1 RB25. No commander. (Tuned for 35R and 550cc injectors, 380whp) $600

Sard 550cc side feed injectors. Fitted to RB25 fuel rail. Ready to bolt in $450

Z32 80mm Airflow meter (with free Apexi air filter) $160 Cheap!

Trust/GReddy RB25 stainless manifold. $350

Trust/GReddy RB25 plenum throttle body adapter to suit standard throttle. $100

Oil Cooler kit from Old HEL group buy. Is missing the Setrab core. $200

Oil cooler core, 9 Row with dash ten fittings. Came from Trust oil cooler kit. Looks weathered/old. No leaks when removed. $50

(Could be used with above kit with adapters for smaller fittings).

R32 (GTST/GTR) Hicas lock bar with the rack ends and new genuine ball joints for the knuckle. $120

R32 Type M front bumper (white), in fair condition. Has had both corners repaired $100

Mesh from R32 GTR bumper. $10

Z32 5 spoke, 16x7.5" wheels (old tyres). $40 Cheaper than tyres!

Riverside Mesh wheels, 16x8 +1. No tyres $250

Set of 4 'Guigarro Design' 2 piece. 16X8, 16X8.5 (5x114.3) (exact offsets between +35 and +45). The offsets marked on the rim may be inaccurate).

Good condition, only two have centre caps. (The 8.5's will not fit on the back of a R32 gtst they foul where the hicas tie rod end attaches to the rear knuckle.

They also will not fit the front because the front calipers). $250

Wheel spacers to suit (Mazda, Toyota, Honda) m12x1.5 thread 20mm. $50

Sparco Bonnet pins, still in packet. $20 Cheap!

Pics of some items posted earlier in thread. New items pics on request. All prices have some negotiation. Contact by PM or SMS 0432227533. Thanks!

MOST PRICES HAVE BEEN DROPPED IN THE INTEREST OF SELLING ITEMS!!!!!! Offers welcome!

  • 2 weeks later...
  • 2 weeks later...
  • 5 weeks later...
  • 1 month later...

Need to sell old parts.

Prices lowered again...

All prices are before postage, bigger items can be sent with courier. Items are located in Brisbane.

Sparco Pro 2000 seat, black in colour. Never been used other than trial fitting. Comes in original plastic and box. $700 NOW $500

Bride RH seat rail, suits R32.33.34GTR. Has N303 on its sticker. $250 Can do a deal with rail and seat together. NOW $150

Sard 550cc side feed injectors. Fitted to RB25 fuel rail. Ready to bolt in $500 NOW $450

Z32 80mm Airflow meter (with free Apexi air filter) $160 Cheap!

Trust/GReddy RB25 stainless manifold. $300 NOW $200

Trust/GReddy RB25 plenum throttle body adapter to suit standard throttle. $130 NOW $80

Oil Cooler kit from Old HEL group buy. Is missing the Setrab core. $300 NOW $200

Oil cooler core, 9 Row with dash ten fittings. Came from Trust oil cooler kit. Looks weathered/old. No leaks when removed. $50 NOW $40

(Could be used with above kit with adapters for smaller fittings).

R32 (GTST/GTR) Hicas lock bar with the rack ends and new genuine ball joints for the knuckle. $120 NOW $80

R32 Type M front bumper (white), in fair condition. Has had both corners repaired $100

Mesh from R32 GTR bumper. $10

Z32 5 spoke pair, 16x7.5" wheels (old tyres). $40 Cheaper than tyres!

Riverside Mesh wheels (pair), 16x8 +1. No tyres $280

Set of 4 'Guigarro Design' 2 piece. 16X8, 16X8.5 (5x114.3) (exact offsets between +35 and +45). The offsets marked on the rim may be inaccurate).

Good condition, only two have centre caps. (The 8.5's will not fit on the back of a R32 gtst they foul where the hicas tie rod end attaches to the rear knuckle.

They also will not fit the front because the front calipers). $300

Sparco Bonnet pins, still in packet. $20 Sooo Cheap!

Pics of some items posted earlier in thread. New items pics on request. All prices have some negotiation. Contact by PM or SMS 0432227533. Thanks!

  • 2 weeks later...

All prices are before postage, bigger items can be sent with courier. Items are located in Brisbane.

Some more items have recently sold, grab a bargain while its here. All reasonable offers considered!

Sparco Pro 2000 seat, black in colour. Never been used other than trial fitting. Comes in original plastic and box. $700 NOW $500 SOLD

Bride RH seat rail, suits R32.33.34GTR. Has N303 on its sticker. $250 Can do a deal with rail and seat together. NOW $150 SOLD

Trust/GReddy RB25 plenum throttle body adapter to suit standard throttle. was $130 NOW JUST $50

Oil Cooler kit from Old HEL group buy. (Is missing the Setrab core). Comes with oil filter adapter, braided lines and fittings. was $300 NOW $150

Oil cooler core, 9 Row with dash ten fittings. Came from Trust oil cooler kit. Looks weathered/old. No leaks when removed. was $50 NOW $10

(Could be used with above kit with adapters for smaller fittings).

R32 (GTST/GTR) Hicas lock bar with the rack ends and new genuine ball joints for the knuckle. $120 NOW $80 SOLD

R32 Type M front bumper (white), in fair condition. Has had both corners repaired NOW $50

Z32 5 spoke pair, 16x7.5" wheels (old but legal 205/55 R16 tyres). $40 Cheaper than tyres!

Riverside Mesh wheels (pair), 16x8 +1. No tyres $280 NOW $200

Set of 4 'Guigarro Design' 2 piece. 16X8, 16X8.5 (5x114.3) (exact offsets between +35 and +45). The offsets marked on the rim may be inaccurate).

Good condition, only two have centre caps. (The 8.5's will not fit on the back of a R32 gtst they foul where the hicas tie rod end attaches to the rear knuckle.

They also will not fit the front because the front calipers). was $300 NOW $200

Pics of some items posted earlier in thread. New items pics on request. All prices have some negotiation. Contact by PM or SMS 0432227533. Thanks!

  • 2 weeks later...
  • 1 month later...

Items are located in Brisbane. All prices are before postage, bigger items can be sent with courier.

All reasonable offers considered!

***** Set of EBC Redstuff Front and Rear pads. (Bought wrong pads for my car. Didn't check on vehicle before returns period expired! My loss is your gain). ***** $250 posted (If you find cheaper will beat!)

- Front Pad DP3775C suit 350Z non brembo, R32 non turbo, Maxima, Altima, Cube, Juke, Sentra.

- Rear Pads DP3686/2C suits S13 CA18, R34 GT-T non turbo, R32 non turbo.

##### Please double check part number before purchase. ######

***** RB25 Crankshaft and Camshafts. Both from series 1 engine. Used condition no damage. **** $100 for both

***** Varex oval style rear muffler with controller and remote. Used for 6 months. Has rear flange. Will need new mounts welded on for indivdual car. **** $350 Offers?

***** Trust/GReddy RB25 plenum throttle body adapter to suit standard throttle. ***** $50

***** Oil Cooler kit from Old HEL group buy. (Missing the Setrab core). Comes with oil filter adapter, braided lines and fittings. ****** $100

***** Oil cooler core, 9 Row with dash ten fittings. Came from Trust oil cooler kit. Looks weathered/old. No leaks when removed. ***** $10

(Could be used with above kit with adapters for smaller fittings).

***** R32 Type M front bumper (white), in fair condition. Has had both corners repaired ***** $50

***** Riverside Mesh wheels (pair), 16x8 +1. No tyres ***** $280 $200

***** 3 inch cat back exhaust for R32 mild steel. Has rear cannon with broken mount, average condition. FREE

Make an offer on parts, if paying cash bargains to be had! Contact by PM or SMS 0432227533. Thanks! :yes: :yes: :yes:

Edited by Kisuu_Buta
  • 2 weeks later...
  • 2 weeks later...
  • 3 weeks later...

Items are located in Brisbane. All prices are before postage, bigger items can be sent with courier.

All reasonable offers considered!

***** Set of EBC Redstuff Front and Rear pads. (Bought wrong pads for my car. Didn't check on vehicle before returns period expired! My loss is your gain). ***** $250 posted (If you find cheaper will beat!)

- Front Pad DP3775C suit 350Z non brembo, R32 non turbo, Maxima, Altima, Cube, Juke, Sentra.

- Rear Pads DP3686/2C suits S13 CA18, R34 GT-T non turbo, R32 non turbo.

##### Please double check part number before purchase. ######

(Photo available on request)

***** R33 Lower control arms, have been professionally boxed with dimpled sheet metal. (Require paint/powdercoating) ***** $180

(Photo available on request)

***** Offset steering rack spacers, great for extra steering lock when drifting etc.***** $50

(Photo available on request)

***** RB25 Crankshaft and Camshafts. Both from series 1 engine. Used condition no damage. **** $50 for both!

(Photo available on request)

***** Varex (oval type) rear muffler with controller and remote. Used for 6 months. Has rear flange. Will need new mounts welded on for indivdual car. **** $300

(Photo available on request)

***** Apexi Power FC to suit S1. No commander. (Tuned for 35R and 550cc injectors, 380whp) WAS $800 now $650

post-47150-0-16009300-1391139217_thumb.jpg

***** Z32 80mm Airflow meter (with free apexi air filter) WAS $160 NOW $120

post-47150-0-17842800-1391138586_thumb.jpg

***** Trust/GReddy RB25 plenum throttle body adapter to suit standard throttle. ***** $50

(Photo available on request)

*****Trust/GReddy RB25 stainless manifold. ***** $300 NOW $200

(Photo available on request)

***** Oil Cooler kit from Old HEL group buy. (Missing the Setrab core). Comes with oil filter adapter, braided lines and fittings. ****** $100

post-47150-0-03488900-1391139996_thumb.jpg

***** Oil cooler core, 9 Row with dash ten fittings. Came from Trust oil cooler kit. Looks weathered/old. No leaks when removed. ***** $10

(Could be used with above kit with adapters for smaller fittings).

post-47150-0-43135600-1391140061_thumb.jpg

***** R32 Type M front bumper (white), in fair condition. Has had both corners repaired ***** $50

post-47150-0-64491700-1391140123_thumb.jpg

***** Riverside Mesh wheels (pair), 16x8 +1. No tyres ***** $280 $200

post-47150-0-88672200-1391140241_thumb.jpg

***** 3 inch cat back exhaust for R32 mild steel. Has rear cannon with broken mount, average condition. FREE

(Photo available on request)

Really need to sell these parts, just collecting dust! Contact by PM or SMS 0432227533. Thanks! :yes: :yes: :yes:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yea that’s why I said ima test them with multimeter and see the reads.
    • Only at idle. Isn’t a problem when rev it seems.
    • @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
×
×
  • Create New...