Jump to content
SAU Community

Recommended Posts

Hey guys,

Thinking about painting the wheels myself. I've never done it before but I looked up some guides and vids on youtube thinking that I could do it.

Heres what I got so far, and correct me if theres any mistakes:

Requirements

1 or 2 Car Jacks

Painters Tape

Lots of Newspapers or those Card thingos

3 or 4 Sand Paper 150-320 grit (any recommendations?, different sources giving different numbers)

2 cans of Primer

2 to 4 cans of Engine/Wheel Paint (any recommendations?, I can only find Duplicolor Metalcast and 3m Engine Enamel Black Gloss or Black Matt, any of these good?)

2 cans of (Resistant?) Clear Coat

Process

1. Remove Wheel properly

2. Clean thoroughly well and Dry

3. Sand wheels and wipe off

4. Tape and cover Tyre

4. Spray with Primer and wait to dry

5. Sand Again ? ? ?

6. Spray with Wheel/Engine Paint and wait to dry

7. Repeat 6 three or four times. (Any recommendations? How many times?)

8. Spray with Clear Coat. (Do I repeat this step too? )

9. Wait 24 Hours before driving.

___________________________

I don't wanna spend a lot of money because I'm poor ! yes.gif

Is it cheaper to get a professional to powder coat it or something?

Before I do anything I got a question, will it look better if the wheels were painted black?

sam0503b.jpg

thanks.gif

Link to comment
https://www.sau.com.au/forums/topic/369543-black-rim-painting/
Share on other sites

first up......I think they will look real nice in black :)

im not very good at painting myself....but for the record....I have painted my dash...my boot....my engine bay....n one thing I can say is sanding is CRUCIAL..n makes ALL the difference !!

For the sandpaper, forget the 150 grit and replace it with 400. 150 is too course, I would only use it to remove a lot of material. When painting, all you are doing is roughing up the surface to give the paint something to grip on to. If the wheels are in relatively poor condition then start with some 240 just to get the imperfections out. You want to spray the 400 to get the best finish, so if the wheels are in good condition then just rough up the surface with the 400 until it loses it's 'shine' and takes on a matte appearance. Make sure you do a really good job of that. Then it's ready to spray.

As for the paint, make sure it is metal paint. Primer is probably unnecessary unless you sand all the way through to metal, you don't need to prime the old paint. Up to you though. But here's the thing: DO NOT LET THE PAINT DRY BETWEEN COATS. The reason for this is there are essentially two forms of paint bonding, physical and chemical. Physical is what you just achieved with the sanding. It is not as good as a chemical bond. If you let the paint dry, you will need to sand it again to make sure it bonds.

What you want to do is let the paint dry to the stage where it becomes sticky to touch but is not completely wet still. So spray the first coat, and then use the overspray on the newspaper to gauge how dry it is. Will probably take about 5 minutes to get to this stage. Then spray the next coat. I would do 5 base coats, and then move onto clear coat. Again, don't wait for the base coat to dry before spraying the clear. Do the same as above. I would do 3-4 coats of clear.

Good luck Eh :)

Dont paint them. I used VHT wheel paint which was meant to be chip resistant. It looked awesome for the first while then they started chipping. Its been a while and they haven't faded at all just the chipping is shit. Almost anything will chip the paint and cause damage to it. I prepped them up pretty well. Gonna sandblast them then have them powder coated.

  • 2 weeks later...

Go matte buddy.

Also a single can of autobarn wheel paint does 2x wheels.

Clean it up with acetone and spray away. I didn't mask mine either.

Pull the wheels off.

Newspaper on the ground.

Acetone the wheels very very well.

Wipe down again with clean rag.

Make sure can has been shaken very well.

First coat, very light. you should still see some of the original colour.

Do the same for the next wheel.

By the time you have done that, move back to the to other wheel and give it another spray.

Move back the to the second wheel, spray.

Wait 5-10mins.

Spray again, move to second wheel.

Wait 5-10mins.

You will get 4-6 coats out of the can.

The wheels will remain 'glossy' until they dry. Do not use the wheels for 24 hours.

Use a consistent sweeping motion, you should be fine.

Don't do it if it is cold outside.

2x $17.50 spray cans

1x $10 acetone

1x $10 Roll of rag

DSC_0808_.jpg

Thanks guys.

Finished painting the first wheel.. so far so good..

Unfortunately for me, I only have 1 jack.. and the spare tyre is deflated.

So 1 wheel at a time for me.

After the last coat, how long should I wait to put it back on the car to dry, so I can do the next wheel?

Of course I won't drive it. But I want to get it all wheels done asap before I have to drive again.

Or is it not a good idea?

Need advice fast !

Thanks thumbsup.gif

1st wheel holding the car now.

I asked my bro if I could borrow his spare tyre and it didn't fit !

So I just got his jack instead.. borrowed my mums jack too so that I could do the next 3! thumbsup.gif

The last 3 wheels are done and now waiting to dry!

post-81658-0-82889600-1310794565_thumb.jpg

Am I doing it right? Looks good to me.

Just waiting for it to dry for the matte black look I guess?

It took me a long time and lots of pain. Maybe not a long time, but constant PAIN!!!-ting. My hands are hurting bad. I'm so unfit !

It's been almost a day and the first wheel doesn't look matte black. I'm getting worried.

Is it normal?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...