Jump to content
SAU Community

Recommended Posts

Hi all... i have conducted a TRUE comparison between the two turbos thanks to Sonic Performance and Garage 7. By true comparison i mean the only thing changed was the turbo. nothing else was touched. The result was suprising and disappointing both at the same time. We found that the GTX version DID spool quicker and hence started making torque and power earlier in the midrange. i now have FULL boost around the 3500 rpm mark which for a turbo like that is impressive. Its highly streetable!

The downside is that for the same boost level peak power is changed by .1 of a kw! its pretty much lineball! the two turbos match each other on the graph pretty much spot on.

runs were done with air temp probe and same correction mode and dyno that STatus uses for real world comparison.

Heres the pics.

Solid pink line is GTX, thin red line is GT.

p1020473s.jpg

p1020471v.jpg

  • Replies 101
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Question:, is running the GTX at the same boost pressure as the other turbo a true 'fair' comparison? I mean... for example if your comparing a gt2871 with a gt4088 you don't leave them at the same boost.

It's interesting to see it ramp hard @ 3500rpm.

And then @ 4000rpm the GTX suddenly stops making power almost as if it's hitting surge. Was that just a case of the tune?

(ie back to back test, no tune adjust?)

Also interesting that its more responsive when other results all seem to show the opposite thus far.

Question:, is running the GTX at the same boost pressure as the other turbo a true 'fair' comparison? I mean... for example if your comparing a gt2871 with a gt4088 you don't leave them at the same boost.

what do you want me to do? run less or more boost?

i feel same boost level should give a truer comparison yes?

Lithium: no tuning.. was just run up. Declan ran out of time on the dyno but the AFR's were the same as before so its still fine.

It's interesting to see it ramp hard @ 3500rpm.

And then @ 4000rpm the GTX suddenly stops making power almost as if it's hitting surge. Was that just a case of the tune?

(ie back to back test, no tune adjust?)

Also interesting that its more responsive when other results all seem to show the opposite thus far.

yeah it probably needs a degree or two added in one part of the map to bring it back inline. this could be due to different airflow charactoristics of the two turbos.

i have seen other peoples results.. but they often have changed other things in their set ups which couldn potentially cause issues. as i said mine is a back to back. use the info as you please.

If the new turbo can flow more than the old one then potentially without raising the boost and/or adjusting the tune to maximize the new found goodness then potentially not really telling of the real difference. That result suggests to me the old turbo had more on it too...

If it didnt nose over hard, it would be looking to pickup a solid ~40kw @ 4500rpm.

Now that would be very interesting indeed.

Good to see a 18psi comparo too where most comparo's have been on 20-24psi for the most part.

Perhaps with more boost the differential between the two would be more noticeable.

Its a good comparison in that most cars are probably only going to run around this level of boost but this result is exactly what I would expect - apart from earlier spool. If you had of reved it to 7500rpm you may have actually seen some results.

I just dont know why you guys are so dissapointed - you only need to compare the compressor maps to see that there are f**k all gains unless your running around 2bar of boost with the gtx.

PS what type of engine management?

Been waiting for this.....the next step is to tune/map for the GTX but don't lift the boost. I reckon the ramp up will likely maintain its margin over the GT a bit better throughout the rev range . But I have a sneaking suspicion that the peak power [for 18psi] will be very similar.

But the GTX would be a lively package on the street, an extra 30rwkw at 3500!!! I'm almost tempted to sell my GT and try one [but I have other plans involving a dirty 30, so this challenge is not for me].

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I had 3 counts over the last couple of weeks once where i got stranded at a jdm paint yard booking in some work. 2nd time was moving the car into the drive way for the inspection and the 3rd was during the inspection for the co2 leak test. Fix: 1st, car off for a hour and half disconnected battery 10mins 4th try car started 2nd, 5th try started 3rd, countless time starting disconnected battery dude was under the hood listening to the starting sequence fuel pump ect.   
    • This. As for your options - I suggest remote mounting the Nissan sensor further away on a length of steel tube. That tube to have a loop in it to handle vibration, etc etc. You will need to either put a tee and a bleed fitting near the sensor, or crack the fitting at the sensor to bleed it full of oil when you first set it up, otherwise you won't get the line filled. But this is a small problem. Just needs enough access to get it done.
    • The time is always correct. Only the date is wrong. It currently thinks it is January 19. Tomorrow it will say it is January 20. The date and time are ( should be ! ) retrieved from the GPS navigation system.
    • Buy yourself a set of easy outs. See if they will get a good bite in and unthread it.   Very very lucky the whole sender didn't let go while on the track and cost you a motor!
    • Well GTSBoy, prepare yourself further. I did a track day with 1/2 a day prep on Friday, inpromptu. The good news is that I got home, and didn't drive the car into a wall. Everything seemed mostly okay. The car was even a little faster than it was last time. I also got to get some good datalog data too. I also noticed a tiny bit of knock which was (luckily?) recorded. All I know is the knock sensors got recalibrated.... and are notorious for false knock. So I don't know if they are too sensitive, not sensitive enough... or some other third option. But I reduced timing anyway. It wasn't every pull through the session either. Think along the lines of -1 degree of timing for say, three instances while at the top of 4th in a 20 minute all-hot-lap session. Unfortunately at the end of session 2... I noticed a little oil. I borrowed some jack stands and a jack and took a look under there, but as is often the case, messing around with it kinda half cleaned it up, it was not conclusive where it was coming from. I decided to give it another go and see how it was. The amount of oil was maybe one/two small drops. I did another 20 minute session and car went well, and I was just starting to get into it and not be terrified of driving on track. I pulled over and checked in the pits and saw this: This is where I called it, packed up and went home as I live ~20 min from the track with a VERY VERY CLOSE EYE on Oil Pressure on the way home. The volume wasn't much but you never know. I checked it today when I had my own space/tools/time to find out what was going on, wanted to clean it up, run the car and see if any of the fittings from around the oil filter were causing it. I have like.. 5 fittings there, so I suspected one was (hopefully?) the culprit. It became immediately apparent as soon as I looked around more closely. 795d266d-a034-4b8c-89c9-d83860f5d00a.mp4       This is the R34 GTT oil sender connected via an adapter to an oil cooler block I have installed which runs AN lines to my cooler (and back). There's also an oil temp sensor on top.  Just after that video, I attempted to unthread the sensor to see if it's loose/worn and it disintegrated in my hand. So yes. I am glad I noticed that oil because it would appear that complete and utter catastrophic engine failure was about 1 second of engine runtime away. I did try to drill the fitting out, and only succeeded in drilling the middle hole much larger and now there's a... smooth hole in there with what looks like a damn sleeve still incredibly tight in there. Not really sure how to proceed from here. My options: 1) Find someone who can remove the stuck fitting, and use a steel adapter so it won't fatigue? (Female BSPT for the R34 sender to 1/8NPT male - HARD to find). IF it isn't possible to remove - Buy a new block ($320) and have someone tap a new 1/8NPT in the top of it ($????) and hope the steel adapter works better. 2) Buy a new block and give up on the OEM pressure sender for the dash entirely, and use the supplied 1/8 NPT for the oil temp sender. Having the oil pressure read 0 in the dash with the warning lamp will give me a lot of anxiety driving around. I do have the actual GM sensor/sender working, but it needs OBD2 as a gauge. If I'm datalogging I don't actually have a readout of what the gauge is currently displaying. 3) Other? Find a new location for the OEM sender? Though I don't know of anywhere that will work. I also don't know if a steel adapter is actually functionally smart here. It's clearly leveraged itself through vibration of the motor and snapped in half. This doesn't seem like a setup a smart person would replicate given the weight of the OEM sender. Still pretty happy being lucky for once and seeing this at the absolute last moment before bye bye motor in a big way, even if an adapter is apparently 6 weeks+ delivery and I have no way to free the current stuck/potentially destroyed threads in the current oil block.
×
×
  • Create New...