Jump to content
SAU Community

Recommended Posts

  On 14/07/2011 at 11:44 PM, dirtyRS4 said:

that would be paul, trev, ross. and, all the guys wanna be like him, all the girls wanna be with him, the one, the only Stinky Rooster!!!!

*crowd goes wild*

FYP Brah! :thumbsup:

  • Replies 50
  • Created
  • Last Reply

Top Posters In This Topic

it doesnt bother to much about price i dont pay for my daily fuel due to i get a fuel card for work but the weekender gets the BP mainly because it was tuned on it and im paro about the difference the other companies have. and i have like 3 BPs surrounding me

is there anything to compare all the other 98 octane fuels. i would like to see how much each manufacturers fuel differs from the other

  On 19/07/2011 at 1:16 PM, Pal said:

mines a daily and at 15l/100 u got to look at the price

Tune it already lol. Don't be like Rohan...

Complaining about fuel economy, yet drives daily... He definitely could've done the tune and had money left over from how rich it was (is) running...

  On 19/07/2011 at 1:18 AM, R31Nismoid said:

A full list of locations around WA can be found in the article on the SAU Main page:

http://www.skylinesaustralia.com/forums/topic/371313-shell-launch-v-power-in-wa/

:cheers:

Yeah! My local Shell is on the list :w00t:

  On 19/07/2011 at 5:31 AM, dan_the_man said:

price difference between BP and shell?

I found BP in general to be 5 - 10 cents more compared to others.

  On 19/07/2011 at 1:43 PM, 10 4 said:

Tune it already lol. Don't be like Rohan...

Complaining about fuel economy, yet drives daily... He definitely could've done the tune and had money left over from how rich it was (is) running...

its getting a couple of grand spent on it next month, springs, cat, tune and alignment. then should be all good.

and wasn't complaining, just stating fact :nyaanyaa:

Hehe, actually a few of my mates have said the same thing. I've ignored my fuel gauge for years now, mainly because it disappears too fast. Nah honestly, providing there's no knock and the engine responds as expected then the criteria is pretty well met

  On 19/07/2011 at 10:21 AM, Pal said:

i use caltex 98 all the time and pay on average 1.45c/l. will have to beat that to swap. I checked bp and it was 1.64c/l, kept on driving >_<

$1.55 p/l for V power at shell on Great northern hwy(midland) yesterday

Shell glengarry or duncraig what ever u wanna call it has now got it available and on 8 pumps, seems to be 15c a litre more then 91 where as caltex is normally iirc only 14c more, but with it's proximity to my house and a liquor land seems a good option for a carton of corona and 4c of me petrol all at once.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
×
×
  • Create New...