Jump to content
SAU Community

Recommended Posts

Seems fair, seeing as you have no idea what you're talking about.

Same could be said for yourself judging by a few of your last posts here and elsewhere.

Sounds alot like tha garbage talk you hear over on NS.com. The fact that you feel the need to personally attack someone to get your point across does not add strength to your argument.

No references to back your argument by any chance?

MrStabby has it right.

R32Abuser you need to re-think your mechanical force concepts.

Let me ask you this...

Assume the clutch and flywheel assembly is at rest.

Induce a torque (via the motor) onto this assembly so that it will rotate.

Now, suddenly, the flywheel is instantaneously stopped. Newtons first law states that the clutch asm will want to continue to rotate. We all know that it will cease to move a very short time after the flywheel stops rotating due to these two items being attached to one another.

What part of the flywheel/clutch assembly transfers this torque reversal? Would you agree that it is the locators/fasteners which fasten/locate the clutch assembly to the flywheel?

It has to be...there is nothing else attaching these two indivdual parts together.

Now, if the dowels are toleranced tighter than the bolts themselves, what else will transmit this torque reversal?

Also,

Since this assembly is not counter-weighted, and since another member has stated that locating is not important, then why are the dowels there? I agree that in some setups (aftermarket) there is no dowels, but does that automatically make them a good/better design?

Edited by R32Abuser

Your very own argument shows that you do not know how the fasteners do their jobs. You had best stop now. You are making yourself look stupid.

No references...? So many credible source must agree with your argument though. Right?

You must be correct though...Nissan (and majority of manufacturers) have done, and continue to do it wrong. You dont need dowels on the flywheel. :down:

Edited by R32Abuser
  • 1 month later...
  • 9 years later...

This is interesting, suggests there is a correct orientation for the flywheel. To which the dowel will assist in getting it right. So as long as you align the dowel holes should be all good, right?

https://www.enginebuildermag.com/2009/08/dowel-pin-alignment-caution-for-nissan-engines/

  • 2 months later...

I can't believe the numpty you were arguing with couldn't grasp-

1. Dowel is for locating

2. Bolts press two surfaces together

 

..and this thread made it to page 2 !

FFS...

  • Like 1
  • Haha 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • But seriously, can we ask for the results of the "tip a bottle of metho into a nearly empty tank" experiment?
    • Hang on. Let me get this straight. The desire is to have coilovers, BC in particular, to be MORE comfortable on Sydney roads than stock suspension? Well, that's obviously not right. BCs have crude damping design at the very best, and typically hard spring rates. BC stands for Billy Cart. And then, the desire is to put in some shitty old worn out stockers, to get it blue slipped and then put the BCs back in? And then.....what? Not worry about getting pulled up by the Plod? Because you seem to have raised a worry about paying for engineering (which actually does solve all your legality problems) and still getting pulled up.... but the only problem there is that if/when that happens you have to show your paperwork at the inspection station. Whereas, if you just swap in borrowed shitty old stockers to get it slipped now, and then you get defected in the future, you have to go find more shitty old stockers then too. You course of action looks like this set of options: Buy brand new stock type dampers, and springs. probably cost a bit more than $1k all up, but will last for the remaining life of the car. Put them in, pass inspection, drive on them forever more. Hell, they could even be really nice Bilsteins and Kings or other lower&stiffer springs if you wanted. Get the car engineered as is. ~$1k. Buy new Shockworks coilvers (or MCA) and also pay for engineering. You're spending a lot more here. But these will be the best things that you could drive around on.
    • Might be worthwhile hitting up Facebook's groups, I know most of them contain terrible people and scammers - however you might be able to find someone that's in Sydney with factory suspension you could purchase and/or hire. Just do not send any form of money anywhere, in person cash only.
    • Thanks @Duncan Ride height is fine. I think it's almost stock tbh. Happy to share a pic. I don't actually have a regular mechanic as haven't lived in Sydney too long. Could you or anyone recommend any shops in Sydney?
×
×
  • Create New...