Jump to content
SAU Community

Recommended Posts

Well, besides looks, not a whole heap. Its all about the size of the contact patch at the end of the day (in performance terms) and if you have the same width wheels in 17" and 18", there is not going to be any noticeable difference.

One thing to keep in mind though is that wider tires are generally easier to get for larger sized wheels, although tires for said wheels are usually much more expensive (for the decent stuff anyway).

LW.

I have 18"s now but would love to go back to 17"s. The ride is noticibly different and you can feel that extra inch of sidewall that goes missing.

Tires also are harder to find and a lot more expensive in 18"s. 17"s are also cheaper initially to buy.

I'm running 17x8's on my 200sx atm, last week i temporily put 18x7.5 on to see the difference. I honestly couldn't believe how bumpy it was with the 18's (i've got koni adjustables set on full firm) Car felt like it was skipping over every minor imperfection in the road.

I guess 18's would look more flashy, but when i see a import with expensive 17's i usually get the hint that it means business!

If you want quicker launches, and better fuel efficiency, go the 17"s, as the 18's will have a higher moment of inertia and take more power to get up to the same speed. this also works with 16"s vs 17"s and so on. it all depends on what you want to do, go fast or look good.

18x7.5 seem pretty skinny, i would think if you were after wheels that performed well as well as looked good, you would probably go for 8 or 9 inch wide wheels, especially for the rear.

I think a car with fat 17x9s looks a lot tougher than a car with 18x7.5. Plus tyres are heaps cheaper.

The only car I had that I ever changed rim diameter was my Aus spec R31. Went from 14 to 15 inch.

I didnt think it would make that much difference but hell was I wrong. The ride is a lot more harsh and would assume your suspension cops more of a beating as there is less tyre profile to absorb some of the shock.

i own an R33 GTS, i was going to swap the axles over to 5 stud to get some good racing 18s (the wheels i am after are only available as 18s in 5 stud). i have been toying with the idea of keeping the 4 stud and getting the 17x8 versions instead. after reading this i think the 17s sound a lot better but i will be doing a turbo upgrade/swap later on - will i need to move to 5 stud and GTSt LSD anyway? in which case i'll just get the 5 stud 17s :rofl:

For a 33, there's not much need to go bigger than 17 x 8 simply because they have a good contact patch, is relatively cheap and they fill out the wheel wells fine.

Same for the 32.

The 34 does seem to look better with 18" rims.

T.

Hell yer .:rofl:

Also at the same time.. I thought by having slightly wider rear wheel will give slightly better tracktion? Since the gtst/gts25t/gtt are all rear wheel drive and all. :D Correct me if I'm wrong of course. :)

Well over the last week I have asked people left, right and centre (owners/tyre salesman/this forum/suspensionexperts) which way to go....

The core of it is... if you got the cash go the 18x8 and 18x9.

I drove both 17's and 18's this week on the same suspension set up (standard) and the ride is hardly different... after all it's just 5mm of side wall difference. I guess the real difference would be around tuning the suspension to suit the wheel size. Sports cars are full of comromise, this is just another one.

lwells 's post was on the mark... it's all about the contact patch.

Cheers

PB8

Rim size and how it performs really depends on the application and how they're set up, Formula 1 cars run 13's yet seem to go ok... don't ya think... They basically use the sidewall as suspension and run VERY hard suspension components to compensate... its down to personal taste and what it is your after, looks or performance and how you tune your suspension to match

18;s dont cost too much more than 17's... but you will take it in the arse with tire prices..... I dont know what 17" rubber goes for these days, but a few weeks ago got a nail through the sidewall on the 350z.. 1x18" tire cost $500 :(

If it was $350 bucks the difference for a new set of 18's (with tyres), which way would you go? I can't see the ride being that much worse as it's only going from a 245 to a 240 anyway.

Cheers

PB8

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
    • Ok, disregard my “rate them” comment, sorry for my unrealistic input
    • OK, now we are ready to get started. You need to remove the air boxes on each side for clearance. The cover is straightforward, undo the clips on the top and lift the front cover out of the rest of the housing. If it is tight you can remove the air filters first. The rear section of the airbox is trickier. On each side you need to remove the Air flow meter wiring which is held to the airbox with a clip; you need to get behind the clip on 2 sides if you want to remove it without breaking it - unclip the harder side and pull on the clip with medium force, then unclip the easier side and it should pop out The airbox is held onto the intake hose with a spring clamp; you need to get a flat bladed screwdriver behind the spring on both sides and pop them outwards. When you have got them in the right unclipped place they will stay there and the airbox slips out pretty freely. Put a rag in the intake to prevent anything getting dropped in there, and also to prevent you seeing that the turbo seal is leaking oil (as they do). Then. The top of the radiator is held by a steel plate, it is secured by 2x10mm and 2x12mm headed bolts . Remove them and remove the plate Also grab the bushings that hold the radiator to the plate on each side so they are not lost!
    • Next, remove the upper and lower radiator hoses, both are held with a spring clamp. While you are under there, tackle the Auto Trans cooler lines.  Again both are held on with spring clamps, and as mentioned above you should cap them on the radiator side with an 8mm cap, and on the car side loop them with a length of 8mm pipe - this will stop you losing a dangerous amount of AT fluid during the rest of the job If you've been meaning to add a sender for AT trans temp, this is a great time to do it; put a sender fitting into the passenger side line as that is the inlet to the cooler/radiator.
    • Next you need to remove the intake duct (as with pretty much every job on these cars), it is a series of clips you gently remove with a flat bladed screwdriver. They do get brittle with time and can break, and I have not found a decent quality aftermarket one that fits (they are all too soft or flimsy and don't last either) but the nissan ones are a couple of bucks each (ouch).  Once the clips are off (either 8 or 10, I didn't check) you lift the intake duct out and will see the reservoirs Undo the line into the radiator side cap (some bent needle nosed piers are awesome for spring clamps) and then remove the 4x 10m nuts that hold both in place.  I didn't get these pics, but remove the line under the radiator reservoir (spring clamp again) then remove that reservoir. Then you can get at the intake reservoir, same thing, spring clamp underneath then remove it. BTW This is a great time to put in a larger (+70%) combined reservoir that AMS makes..... https://www.amsperformance.com/product/q50-q60-red-alpha-coolant-expansion-tank/ They also make an Infiniti branded and part# version if that is your thing
×
×
  • Create New...