Jump to content
SAU Community

Recommended Posts

G'day

I have always thought about the idea of holding the wastegate open on a standard rb25 (or any turbo car for that matter) to see how it affects the fuel economy.

Here's my theories-

-wastegate open turbo wont make boost

-no build up of pressure will be read through boost sensor and therfore adjust fuel mixtures to suit

-less pressure = less fuel but is it still at the right mixture???

I have designed a Simple circuit that will do this with the flick of a switch (pneumatics background). My guess is on open roads you wont notice any difference in fuel economy as 95 percent of the time you are off boost anyway. But driving through the city even if you are light on the old pedal it still comes on and off boost fairly often.

The only thing I am not clued up on is the detailed workings of the ecu, how it calculates correct fuel delivery and the long term effects of running continuously like this specifically any possible damage to the turbo and engine. for now lets assume its a pretty standard setup i.e. no fuel or turbo mods, standard block and ecu and maybe an exhaust/frontmount (ive got a rb25det neo in a stagea rs4 which is stock standard).

Also please dont start with the whole "if you dont like paying fuel bills for a turbo car then buy a friggin hybrid" talk because I dont pay for my fuel so at the end of the day it doesn't bother me a great deal. Honestly its a simple mod that could be done to any stocker in about 2 hours with a switch and everything and would cost under 400 bucks for the whole setup.

Thanks in advance

Cheers Rick

Link to comment
https://www.sau.com.au/forums/topic/371517-wastegate-held-open/
Share on other sites

I don't think it'll help fuel econ at all, because you're still moving the same mass to the same speed over the same time so boost or no boost.

Air going into the engine is measured though a mass air flow meter so yes with less boost you'll be flowing less air but you're still moving the car around with the same engine so I doubt it'll make a difference to fuel econ.

If you want better fuel econ, get a nistune daughter board for your ECU and get it tuned and tell your tuner you only want better fuel econ, not more power, get rid of that stupid dual stage boost thing that stags have and you'll live the fuel econ dream.

Edited by zoidbergmerc

Drive an SR20 with a T28. They seem to have this awesome balance where they can spool quick or with the control of your right foot be extremely economic and good offboost for drivability.

IMHO you want the turbo spooling to some extent, you just dont want it making positive pressure without reason.. The situation is more dynamic than 'less air = less fuel' unfortunately.

A very senior CAMS official once told me one of the group A teams let him drive their MA70 supra while it was in development. He told me when they went from the stock turbo to their race item the car became MUCH better to drive and multiple times more economic.

I think the trick here is the right turbo.. Having something that has some nice offboost spool but ready to take action with half a hint (50% throttle :P)

THe trick is just right foot. IF I can get 450-500km around town in a 360rwkw 1700kg+ car... No O2 sensors either... Then you are doing it wrong if you can't get better.

IF you use low amounts of throttle, youll barely come near boost.

If you intend to have the gate open 100% of the time, and use more throttle... You will still eat fuel boost or no boost as its all about right foot control and a DECENT tune. not a 250 mail order special.

The trick is just right foot. IF I can get 450-500km around town in a 360rwkw 1700kg+ car... No O2 sensors either... Then you are doing it wrong if you can't get better.

However true, 360rwkw out of a twin turbo 2.6L is also a lot of off boost flow under the pedal. In my experience, even the stock turbos on the R32 GTR are a whole lot of play before you need to worry about boosting unnecessarily.

A factory turbo RB25, I believe, is a very different ball game. A useless SOD of an item IMHO.

Also, the mail order Toshi tunes definitely seem to be quite successful. I mean, its not like Nissan tuned an ecu for every individual car.

lol at this thread entirely.

I love the way people think that they have a better idea over a few beers than years and millions of dollars in R&D.

If this is such a great idea, nissan would have thought of it. Back in the 1980s.

so how you going to pressurise the actuator to hold the gate open? you going to have a pressure cylinder somewhere to store the pressure.

Also by doing this you effectively have a low compression 2.5 litre that still has a reasonable exhaust restriction, the cam profiles aren't optimised for what you are trying to do and due to the low compression your fuel economy will not be good. The reason manufacturers use high compression engines is to increase efficiency to increase fuel economy.

Edited by D_Stirls

Pretty sure the new BMW turbo 335i does this. Wastegate is open always, unless you put your foot down, then it closes, and then regulates boost.

This way, it fails "open" so you would never accidently get an overboost situation :)

Could be emissions related too?

so how you going to pressurise the actuator to hold the gate open? you going to have a pressure cylinder somewhere to store the pressure.

Also by doing this you effectively have a low compression 2.5 litre that still has a reasonable exhaust restriction, the cam profiles aren't optimised for what you are trying to do and due to the low compression your fuel economy will not be good. The reason manufacturers use high compression engines is to increase efficiency to increase fuel economy.

Makes sense when its said it this way. the actuator actually opens with vacuum its simple using a 3/2 solenoid valve and a check valve 400 dollars in my first post is a little off the mark... the solenoid valve is about 120 dollars and the check valve is about 50 dollars add your electrical relays, switches a bit of wiring ect. thats all you need. I can get from penrith to jindabyne fully loaded with ski gear, 4 adults and a roof pod and have just under a quarter of a tank left.

I have tried it out driving up and down the street and it works a treat... all I am worried about is getting wrong fuel mixtures and damaging something cause of a bad mixture

Edited by Space Goat

if you are bringing the engine onto boost you are well past TPS being basically closed, ie %20 TPS

so if you find its coming on boost, then you are pushing the pedal too hard

you could have a T88 big single RB26 and still get 450kms+ to tank like ash said

its all how you drive the car

imho wiring the wastegate open or shut achieves zero for fuel control

the airflow meter drives fuel injection control so wastegate open or closed, its the same

you pushing the pedal more than needed is what drives more airflow meter load

imho wiring the wastegate open or shut achieves zero for fuel control

the airflow meter drives fuel injection control so wastegate open or closed, its the same

you pushing the pedal more than needed is what drives more airflow meter load

I would have thought that if your car is off boost the pressure of the air that your engine is using is at atmospheric pressure (or under vacuum close enough). if your car is on boost then the air your engine is using is under pressure... wouldn't this mean to achieve a desireable air/fuel ratio when your car is on boost it must use more fuel... wouldn't this mean there is less air passing through the air flow meter??? a standard rb25 at say 7 psi (.5 bar), needs 1.5 times more air to run at the same revs as one that was running at atmospheric pressure.

the actuator actually opens with vacuum

Sure about that? Unless your pulling from that other side of the diaphragm, but even then where the shaft leaves the can isn't sealed in 90% of actuators. You talking waste gate actuator or some other actuator in your setup?

I have tried it out driving up and down the street and it works a treat... all I am worried about is getting wrong fuel mixtures and damaging something cause of a bad mixture

The mixtures will be fine.

Edited by D_Stirls

you are going way too technical for something that's not a problem

all for trying new things

but on light cruise

ecu is in closed loop feedback

TPS is usually around %5

wastegate is closed

pressure is around -200mmhg

when you open the throttle

ecu is not in closed loop feedback

TPS is usually around %15

wastegate is closed

boost pressure may be zero or may just sit around 0.0kgcm2, ie past vacuum

when you are on light cruise the turbocharger is effectively a paperwork

there isnt enough velocity to make boost or as we call it "to tell the computer - hey throw in tons of fuel were making boost"

Sure about that? Unless your pulling from that other side of the diaphragm, but even then where the shaft leaves the can isn't sealed in 90% of actuators. You talking waste gate actuator or some other actuator in your setup?

The mixtures will be fine.

Sorry my bad your correct otherwise it will over pressurise and could not regulate :P ... i think it slightly built up boost the first time it was on and then with the check valve configured correctly it held pressure in the wastegate from then... I might give it a try and see how it goes with a full tank of city driving

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...