Jump to content
SAU Community

Recommended Posts

I had read that somewhere, but couldn't justify the price for a street car, vs some spacers and bolts that cost me nothing.

Yep, I hear you.

I can get these for far less than RRP if you ever decide you want them.

  • Replies 71
  • Created
  • Last Reply

Top Posters In This Topic

I machined up some spacers (just a thick washer really), you could use a stack of washers if you really had to. If you want I could make you some spacers out of ally, and get the bolts for you. pm if you want it.

No worries, I do the H/D Links for $135 a pair; bar prices I'm happy to PM.

Is it worth my time throwing together a fresh group buy?

If we can get 5 people to confirm their interest; I'll get one together.

Prices would be increased possibly $10-$15 per bar over my original 2011 Group buy prices.

http://www.skylinesaustralia.com/forums/topic/372067-c34-stagea-sway-bar-group-buy/

I think I spoke to you at the Putty Road cruise regarding this and was too lazy/busy to follow up. :(

Looking at sway bars for the V35 but not sure on what to go with. Factory, it has a 34mm front and 24mm rear. Considering that I can't see any larger sizes, not sure what the benefits would be?

If there are benefits, then I'd be interested in joining a GB considering if all things line up :)

I think I spoke to you at the Putty Road cruise regarding this and was too lazy/busy to follow up. :(

Looking at sway bars for the V35 but not sure on what to go with. Factory, it has a 34mm front and 24mm rear. Considering that I can't see any larger sizes, not sure what the benefits would be?

If there are benefits, then I'd be interested in joining a GB considering if all things line up :)

Hi Tony, I do remember having a chat actually!

Don't forget the OEM bars are hollow; so going to the 32mm solid front & 20mm solid rear is a huge increase in roll stiffness.

Yours I can do as a one off anytime; so when you are ready mate.

Hi Tony, I do remember having a chat actually!

Don't forget the OEM bars are hollow; so going to the 32mm solid front & 20mm solid rear is a huge increase in roll stiffness.

Yours I can do as a one off anytime; so when you are ready mate.

Of course you remember the dark guy in a SAU QLD polo rolling in a N16 Pulsar! :P

I was looking at one of the companies in the states and they had the same sizes as factory - must be solid then. Can you acquire these, and if so what dorras are we looking at? Feel free to PM me if required :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • What are we supposed to be seeing in the photo of the steering angle sensor? The outer housing doesn't turn, right? All the action is on the inside. The real test here is whether or not your car has had the steering put back together by a butcher. When the steering is centred (and we're not caring about the wheel too much here, we're talking about the front wheels, parallel, facing front) then you should have an absolutely even number of turns from centre to left lock and centre to right lock. If there is any difference at all then perhaps the thing has been put back together wrongly, either the steering wheel put on one spline (or more!) off, and the alignment bodged to straighteb the wheel, or the opposite where something silly was done underneath and the wheel put back on crooked to compensate. Nut there isn't actually much evidence that you have such a problem anyway. It is something you can easily measure and test for to find out though. My money is still on the HICAS CU not driving the PS solenoid with the proper PWM signal required to lighten the load at lower speed. If it were me, I would be putting either a multimeter or oscilloscope onto the solenoid terminals and taking it for a drive, looking for the voltage to change. The PWM signal is 0v, 12V, 0V, 12v with ...obviously...modulated pulse width. You should see that as an average voltage somewhere between 0V and 12V, and it should vary with speed. An handheld oscilloscope would be the better tool for this, because they are definitely good enough but there's no telling if any cheap shit multimeter that people have lying around are good enough. You can also directly interfere with the solenoid. If you wire up a little voltage divider with variable resistor on it, and hook the PS solenoid direct to 12V through that, you can manually adjust the voltage to the solenoid and you should be able to make it go ligheter and heavier. If you cannot, then the problem is either the solenoid itself dead, or your description of the steering being "tight" (which I have just been assuming you mean "heavy") could be that you have a mechanical problem in the steering and there is heaps of resistance to movement.
    • Little update  I have shimmed the solenoid on the rack today following Keep it Reets video on YouTube. However my steering is still tight. I have this showing on Nisscan, my steering angle sensor was the closest to 0 degrees (I could get it to 0 degrees by small little tweaks, but the angle was way off centre? I can't figure this out for the life of me. I get no faults through Nisscan. 
    • The BES920 is like the Toyota Camrys of coffee machines. E61 group head is cool, however the time requirements for home use makes it less desirable. The Toyota Camry coffee machine runs twin boilers and also PID temp control, some say it produces coffees as good as an E61 group head machine.
    • And yes with a full tank it will hit limiter free revving or driving 6B6CDF6E-4094-426D-A9CB-6C553475FE36.mp4
    • One way of putting the fuel surge idea to rest, is that even when in neutral/clutch in or free revving it still has the same issue, it can’t even get to limiter (7800) so to me that says it can’t be g force, I’m not trying to argue I just want to find the f&$king issue 😡
×
×
  • Create New...