Jump to content
SAU Community

Recommended Posts

ok so i have searched and read through about 40 of the 75 odd pages in the skyline wheel fitment thread...

found a couple similar results...

after pics of fitment with stock guards (obviously flared/lipped) on a 32 GTST with

17x9.5 +12

fitted with 215, 225 or 235 40 or 35 series tyres. Rims are already on the way so just sussing out sizes. fronts running -3.5 camber rear camber is -0.75, would rather do guard work than change alignment settings ;)

Link to comment
https://www.sau.com.au/forums/topic/372204-r32-gtst-fitment-pics-please/
Share on other sites

Here's mine with 17x9 +5 and a 215/45R17 on the front. I haven't had my camber measured but at a guess I'd say I'm running about -3deg. Your rim would stick in 1mm than mine but not sure about what tyre you'd wanna run.

016zm.jpg

As for the rear you'll need a small flare I reckon.

Hope this helps a bit.

thanks bud keep em coming...

currently running 17x9.5 +12 on the rear with a 215/45 federal and pokes a bit, front are 17x9 +15 with 225/45 and sit flush .. just unsure on 18s and tyre profile...

was wanting to run lower profile but not too sure how this is gonna stretch.

18x9.5 +15 all round

stock flared guards

235/40/18 feddy 595ss

low.

now camber arms or anything.

post-16535-0-03996200-1311747147_thumb.jpg

post-16535-0-17972900-1311747172_thumb.jpg

mannn thanks so much this is exactly the specs i was looking at and ive been wondering for ages if it will work with no camber arms, you rule!

thumbsup.gifworship.gifthanks.gif

i did my guards.

they were rough as i had 1 day to do them before hitting the track, i got them much better after when i had time.

use tape to tape up how you like the flare, then use a hammer and smash the shit out your guards.

i started hitting soft but realised i needed to hit HARD..

I'm just about to purchase some rota Grids in 18x10+22 and 17x9+15

I know these would need some guard work and some neg camber, but any idea how much. Shouldnt be heaps if i have some stretch on the tyres, rears especially?

This is on stock 32 gtst guards btw

I ran 18 by 9 +22 and with 235's it rubbed even with lipped guards and max camber on the rear, fronts were just ok with camber and caster arms.

Imo with stock guards and mild lipping a 9 +22 is as low an offset as you should go.

There is still alot of clearance inside on the rear so a 9.5 or 10 should fit easy with correct offset.

Btw running anything smaller then a 235 on a 9.5 is stupid and dangerous, if you cant fit the wheels properly dont buy em.

Unless you want to roll and pull the guards a little then a 9 +25 ish is good on the front, the rear can have wider, say a 10 but the offset has to be right.

There is also issues with inner clearance on the front, especially with 18's as they only just cleared the sideskirts and front bar.

IMO 17's are a good compromise between looks and practicality. 18's look better but you can fit 17's alot easier, I have just bought some 17 by 9 +22's and even with 245's they didnt really rub, nothing compared to the18's which rubbed on every corner on the back.

Plus 17's are alot cheaper for tyres :thumbsup:

  • 3 weeks later...

305967_10150260356386831_683216830_7893687_334757_n.jpg

so the rears fit.... 235/40/18 with 18x9.5 +12

unfortunately I didnt think about the effect having a 33 LCA up front would have on the track so they sit about 12-20mm from the guards... going to try massage guards some more, failing that go a weaker offset.. this is a last option lol.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...