Jump to content
SAU Community

Can Someone Identify This Gearbox?

Sammy B
 Share

Recommended Posts

Sammy B Contributor

Sammy B

Posted
Posted (edited)

Hey all, Ive got a 32gtst with a standard rb20 in it, and what i thought was the standard box, but have been told this is not an RB20 box.

Just trying to work out what it is, and if it's ok to continue using it in my car/or what I should sell it as.

Notice the gearbox is mounted using only 2 holes, and also the shifter sits slightly forward:

Any help would be great,

Cheers - Sam

post-77777-0-05935100-1311749191_thumb.jpg

post-77777-0-02527500-1311749225_thumb.jpg

post-77777-0-11798200-1311749256_thumb.jpg

post-77777-0-57702800-1311749268_thumb.jpg

Edited by Sammy B
Link to comment
https://www.sau.com.au/forums/topic/372236-can-someone-identify-this-gearbox/
Share on other sites
The Dan Grand Master

The Dan

Posted
Posted

That looks like a CA/SR box, is the yoke sticking out, at the rear of the box? that crossmember is bolted in backwards aswell by the looks of it

CA/SR has the starter motor bolts facing the other way and no the crossmember is around the right way. The high side is the exhaust/passenger side

turboedsloth Grand Master

turboedsloth

Posted
Posted

That gearstick position is what happens when you put RB20 manual into RB20 auto body. The holes are in different locations. Not a problem, except it causes the rubber boot to push the gear stick backwards a little when in odd numbered gears.

My 32 was auto before its conversion and i don't have this problem

Sammy B Contributor

Sammy B

Posted
  • Author
Posted

Have you had your vehichle fasted? You can see if it came from factory with an auto.

No, I have not had it fasted. That may help work out if it was perviously auto, but I still have no solid idea what that gearbox is from. Also if it is a ca/sr box is there any reason why I shouldnt continue using it?

Any thing i should check/pictures i could take to help determine what it is?

toffy Veteran

toffy

Posted
Posted

Well, so was mine, and I do (although it's not a problem). Must be different by year or something.

could be a r31/vl gearbox . as for the hole position , i vaguely remember a friend of a friend of a friend of a mate telling me that they spaced the front crossmember/engine mount points (or something like that) slightly different in the auto (something about the bellhousing on the auto bla bla) .

Disclaimer: don't take this information as gospel , i didn't personally discover this nor have any intrest at the time of what the guy was talking about so information is fairly sketchy

GTSBoy Grand Master

GTSBoy

Posted
Posted

could be a r31/vl gearbox . as for the hole position , i vaguely remember a friend of a friend of a friend of a mate telling me that they spaced the front crossmember/engine mount points (or something like that) slightly different in the auto (something about the bellhousing on the auto bla bla) .

Disclaimer: don't take this information as gospel , i didn't personally discover this nor have any intrest at the time of what the guy was talking about so information is fairly sketchy

I've had both an RB20DET box and the current RB25DE box in there and the stick position is dead the same. Apart from ratios, those two boxes are identical anyway. Can't comment on stick position of RB30E box, as I have had one within 20' of my car.

waxracing Experienced

waxracing

Posted
Posted

You have the wrong mount on the back as well. There is about 5 different brackets for nissan. they are a,b,c,d,e

I think you need the ( a ) bracket for that conversion and it will line up with the bolt holes for the original mount

webber Proficient

webber

Posted
Posted

i still reakon, it is a short type fs5w71 bolted to an RB20 bell housing.

same crap as they are talkign about below (but obviously dif. combination of boxes, most of the bell housings are the same length, but the main shafts vary in length after the sandwich plate, and the rear of the box can be longer & shorter depending on what it is or in, sometimes you have to change the input shaft or the front bearing plate that bolts to tht bell housing. you get what i am saying

http://club-s12.org/v3/index.php?topic=12333.0

Sammy B Contributor

Sammy B

Posted
  • Author
Posted

Just checked the plate on the firewall, appears it did used to be auto (reads RE4R01a)

If its working fine just leave it there

Working fine, but the clutch is on it's way out, so the box has gotta come out either way (just a matter of whether it goes back in or not)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      R33 Fuel Pump & Brakes after alarm swap

      By MBS206 · Posted

      Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
    • GTSBoy
      R33 Fuel Pump & Brakes after alarm swap

      By GTSBoy · Posted

      Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • GTSBoy
      After market rear camber arm adjustment

      By GTSBoy · Posted

      Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Jarsky
      R33 Fuel Pump & Brakes after alarm swap

      By Jarsky · Posted

      Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Duncan
      After market rear camber arm adjustment

      By Duncan · Posted

      Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
×
×
  • Create New...