Jump to content
SAU Community

R34 Gtr Issue

Johnny

By Johnny,
in Engines & Forced Induction

 Share

Recommended Posts

Johnny Veteran

Johnny

Posted
Posted

Hi there guys,

I have a little issue with my GTR, basically it loses power while driving then seems to come back in a few seconds.

The first time it happened i was driving completely normally, it was starting to build boost @3200rpm or so, the car lost all power and rpm dropped to just under 1000rpm. I immediately stopped the car and turned it off, when i restarted it one minute later it drove fine but happened again 2km later, just before i got home.

So far my troubleshooting yielded without success:

-Bad battery; as i hardly drive it the battery was dying so i changed it to a new high cca battery

-cleaned elec connection points for CAS

-cleaned AFM

Still to come/ideas

-Ordered new spark plugs and splitfire coils

-Bad CAS?

Ruled out:

-Loose cooler pipe as on WOT, boost holds strong.

-No backfires or running rich (no black puffs of smoke)

-No knocks (under 20)

Basically these intermittent faults are the worst cos the car seems fine, starts fine, drives fine and power feels the same so before i must take it to the professionals im hoping someone can maybe help; maybe had the same issue before?

I would be very appreciative of any help or advice given as i know this forum is one of the best when it comes to helping out fellow skyline/car enthusiasts.

-Johnny

Link to comment
https://www.sau.com.au/forums/topic/372332-r34-gtr-issue/
Share on other sites
Johnny Veteran

Johnny

Posted
  • Author
Posted

You guys are rockstars, it was some loose wires/connection of the AFM.

started the car just now, jiggled the airbox and the car stalled.

now ive just gotta figure out how to fix the plug. Can anyone shed some light on how to rewire the plugs or replace them all together? as i dont want this to happen again.

Can I buy new ones or does it require cutting them off and resoldering them back? I do wish to buy new plugs just for piece of mind or are they hardwired into the entire loom?

Again, thanks so much to you all.

-Johnny

Link to comment
https://www.sau.com.au/forums/topic/372332-r34-gtr-issue/#findComment-5939108
Share on other sites
GTSBoy Grand Master

GTSBoy

Posted
Posted

Just note - it may not be the connector/wiring at all. Just as all three guys above have said, the fault is common and it is inside the AFM. Dry solder joints that don't conduct properly all the time. Subject to vibration. The AFM can be opened up and repaired (which is fiddly) or you can just swaptronics it.

Link to comment
https://www.sau.com.au/forums/topic/372332-r34-gtr-issue/#findComment-5939244
Share on other sites
R31Nismoid Grand Master

R31Nismoid

Posted
Posted

Yep it's not the plug, its the gizzards of the AFM.

Time for Nismo upgrade, dont waste time with 2nd hand AFMs. It'll just keep happening.

People have had some success with repairing them, but sometimes not (as in problem comes back later)

Link to comment
https://www.sau.com.au/forums/topic/372332-r34-gtr-issue/#findComment-5939327
Share on other sites
Johnny Veteran

Johnny

Posted
  • Author
Posted

Yep it's not the plug, its the gizzards of the AFM.

Time for Nismo upgrade, dont waste time with 2nd hand AFMs. It'll just keep happening.

People have had some success with repairing them, but sometimes not (as in problem comes back later)

Im sure your right about the need to swap for some new AFM's and nismos would be the way to go but will need to be put on the dyno to map it.

Main thing id like to do is check which is the culprit, the plugs or the AFM's themselves

does this idea seem the way to go:

-get/borrow some standard AFMs to fit and see if that fixes the prob, if that works then i will buy the nismo units but if its just the plugs/wiring then simply fix them

I just checked the car again and it seems its either the lower AFM or plug/wire that is the one that need replacing.

what u think?

Link to comment
https://www.sau.com.au/forums/topic/372332-r34-gtr-issue/#findComment-5939772
Share on other sites
R31Nismoid Grand Master

R31Nismoid

Posted
Posted

In my experience it is always the lower AFM. It would make sense as its closer to the heat etc.

I highly doubt it will be the plug, your car is not old enough. If it was a R32 GTR then i'd say possible.

The wires are nice and thick/simple compared to whats inside the AFM/circuitry being the reason (if you'd seen one apart, you'll know what i mean).

Just because you jiggle and it plays up, is the tell-tale sign the internals of the AFM are dead.

Link to comment
https://www.sau.com.au/forums/topic/372332-r34-gtr-issue/#findComment-5939799
Share on other sites
Johnny Veteran

Johnny

Posted
  • Author
Posted

In my experience it is always the lower AFM. It would make sense as its closer to the heat etc.

I highly doubt it will be the plug, your car is not old enough. If it was a R32 GTR then i'd say possible.

The wires are nice and thick/simple compared to whats inside the AFM/circuitry being the reason (if you'd seen one apart, you'll know what i mean).

Just because you jiggle and it plays up, is the tell-tale sign the internals of the AFM are dead.

Alright then, thanks ash. ill order some nismo's then. can i drive the car to the workshop or will the tune be completely off until i have it tuned on the dyno? maybe tow it down?

Link to comment
https://www.sau.com.au/forums/topic/372332-r34-gtr-issue/#findComment-5939832
Share on other sites
Johnny Veteran

Johnny

Posted
  • Author
Posted

I doubt it will run well enough to be driven.

I accidentally flicked my Nismos over to stock a while ago & the car ran rather poorly :D

Just fit them there, doesnt take too long

I see your point ash. My plan is now to buy a set of second hand OEM AFM's so i can actually drive the car.

As per my previous thread of my stage 2 upgrade, i have new -9 turbz and cam gears sitting around so ill either buy nismo AFM's to pop in or simply swap my power fc to a d-jetro and eliminate them all together.

Ill search on the pros/cons of these ECU's and might even consider the VIPEC; then again, after all the hype surrounding them - has it died down yet lolz.

thanks again man.

Link to comment
https://www.sau.com.au/forums/topic/372332-r34-gtr-issue/#findComment-5940999
Share on other sites
Johnny Veteran

Johnny

Posted
  • Author
Posted

UPDATE: Ive decided to buy nismo AFM's for my car, having it towed to my tuner next week but until then im looking for stock of nismo AFM's

Do any traders or members on here have/sell them and have them in-stock to buy now?

Link to comment
https://www.sau.com.au/forums/topic/372332-r34-gtr-issue/#findComment-5945358
Share on other sites
Johnny Veteran

Johnny

Posted
  • Author
Posted

I managed to find a member who has some nismos for sale which im buying and some standards from another member which im gonna buy too.

my plan now is to use the standards while i collect the last mods needed for my next mod stage and do it all at once.

Another question to anyone in the know:

I will have a set of stock AFMs where one dosent work and i know that sometimes for budget reasons, another member of the forum will need a replacment set who might be a bit tight on cash for z32s or nismos.

Can i have my current set repaired?

they currently work fine when cold but once at operating temp, they stop working; simply a wiring issue maybe? if its a cheap fix then i can fix them supply them to someone else in need.

Might be far fetched but just wanna be able to help another member as i have had plenty of advice and help myself and would like to do the same sometime.

-Johnny

Link to comment
https://www.sau.com.au/forums/topic/372332-r34-gtr-issue/#findComment-5948579
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...