Jump to content
SAU Community

Recommended Posts

Is it only in 1st? K&N pods are oiled, and have had bad experiences of the oil on them getting on the afm hotwire, a spray with a bit of electrical contact cleaner helps that out. Other things are make sure it's not overboosting and hitting boost cut (could be a line disconnected/not plumbed right), or other things I'd check are change spark plugs, if they're new, could be coilpacks giving out under load.

Link to comment
https://www.sau.com.au/forums/topic/373518-stagea-choking/#findComment-5957967
Share on other sites

I'm gonna throw boost cut into the mix, have you

Got a gauge fitted?

Mine has a similar issue, had it when it was stock and still does it mow, just not as bad, with every breathing mod I've done it has gotten better.

I'm running standard boost control, full 3" turbo back system with a blitz pod, and my car makes 0.9 bar of boost, ie 12-13 psi. Maybe yours is like mine and it is over boosting.

Link to comment
https://www.sau.com.au/forums/topic/373518-stagea-choking/#findComment-5958303
Share on other sites

If its airflow cut you'll know when you hit it. It's a complete engine cut, feels like the throttle got slammed closed and the engine revs down. By the way S1's don't have a boost cut, no way for the ecu to know the boost pressure.

Has it always felt this way? Or just recently? The stock setups on all rb's is fairly restrictive especially the exhaust, and the stock mapping doesn't favor consistent pull through the rev range, they tend to flatten out around 4500rpm.

Link to comment
https://www.sau.com.au/forums/topic/373518-stagea-choking/#findComment-5958391
Share on other sites

hey guys thanks for replying. its not sparks as i have new lithium ones. i dont hink its air flow coz my revs stay high all the way till it changes gear and keeps driving normal. its not just in fisrt gear. i first noticed it couple months after i got it which is when i put my k&n on. so maybe it is my afm?

sorry i said my car is stock but i didnt think about but i have a 3" all the way and a hi-flow cat. I got the cat put on coz i thought that was the problem. then i got my dump pipe changed and that didnt fix it either. it already came with massive exhaust when i bought it.

so its either the FM or coilpacks?

ive researched abit n thought maybe the ecu needs tuning. i dont know how it works. this is my second car but my first turbo. man the stagea is awwesome.

thanks for your help guys. please keep helping. some mechanics dont even know what a stagea is.

Link to comment
https://www.sau.com.au/forums/topic/373518-stagea-choking/#findComment-5960043
Share on other sites

Overboosting is usually caused by a dodgy boost controller, or when you have the stock set up could be vacuum lines not set up correctly.

I'd say it's either your coilpacks or AFM though. Easiest/cheapest option would be try to give the AFM a good clean with contact cleaner first.

Link to comment
https://www.sau.com.au/forums/topic/373518-stagea-choking/#findComment-5960169
Share on other sites

Somewhere there is a thread on checking the soldered joints insde the AFM connector. I did not do that as I had a spare.

If cleaning the sensor wire does not fix it, see if you can find the fix it thread.

Link to comment
https://www.sau.com.au/forums/topic/373518-stagea-choking/#findComment-5961246
Share on other sites

Hey Guys thanks your support and help. Got my stagea from mechanics yesterday and it's running smooth. I didn't know they go so hard. Turns out the choking problem was related to my spark plugs. I didn't install them properly.I just put them in and didn't do the whole right measurement thing. Don't kno what it's called. Thanks guys. I'm happy with my car now. Also got a boost gauge so I can keep a eye on turbo. also had manifold replaced coz I had a tink crack.

Link to comment
https://www.sau.com.au/forums/topic/373518-stagea-choking/#findComment-5970844
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...