Jump to content
SAU Community

Rb25, Rb30, Td06, Os Giken

Buckna
 Share

Recommended Posts

Buckna Community Regular

Buckna

Posted
Posted

Alright, have a few things to sell, all this was going to go into my latest project but I have bought a new engine setup for it now.

Have, rb25det. complete inlet and exhaust side, missing turbo, has Greddy adjustable exhaust cam gear, full loom and ecu, loom has been modified previously, suit conversion. has coilpacks, injectors, etc.

Timing belt idler was a little noisey, so has been pulled off and is awaiting a new timing belt, haven't done this yet.

$1000 as is, or $1200 with new gates timing kit installed.

Z32 300zx gearbox (same gearset as RB25 r33 gearbox) with RB25 bellhousing on it, ready to bolt to RB20/25/30. good condition.

$1000

OS giken twin plate clutch, still heaps of meat left on it. comes with flyhweel, clutch plates, intermediate plates and pressure plate. good clutch. retails for around 2.5k

$650

Trust TD06 25g. Have the big td06 also, just been rebuilt, new bearings and seals, T3 footprint 16cm exhaust housing. great condition, will easily go over 500hp.

$1000

Nitto 40mm wastegate, brand new, all flanges included.

$150

Forged RB30 bottom end. ACL forged pistons, block bored to suit, crank linished, new bearings all throughout, RB25 oil pump, RB30 new waterpump, New rear main seal, comes with sump, ring gear, balancer, timing case. Ready for either RB25 or RB30 head.

$850

Can include full reconditioned RB25 head, 1.2mm metal headgasket, head modified to suit RB30 block, cleaned, decked, valves ground and seated, vacuum tested. Assembled on engine,

$1700 complete assembled RB30/25 motor.

BMW E36 318is Getrag 5 speed gearbox and clutch setup, Unneeded, box is perfect, clutch looks ok. Can come with twincam engine as well.

$700

All located brisbane CBD. contact buckna. 0427282562

Link to comment
https://www.sau.com.au/forums/topic/373987-rb25-rb30-td06-os-giken/
Share on other sites
tridentt150v Grand Master

tridentt150v

Posted
Posted

Forged RB30 bottom end. ACL forged pistons, block bored to suit, crank linished, new bearings all throughout, RB25 oil pump, RB30 new waterpump, New rear main seal, comes with sump, ring gear, balancer, timing case. Ready for either RB25 or RB30 head.

$850

what rods?

riley Collaborator

riley

Posted
Posted

still have the rb30 block? price shipped to darwin 0830? is the block all inclusive ie. pulleys, sump, crank,etc...

keen as to buy for a 30/26 convo. will have shipped to ballistic customs.

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kapr
      RB20DE NEO smallbox clutch.

      By Kapr · Posted

      Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • GTSBoy
      What brakes on R34 GTT(Europe)

      By GTSBoy · Posted

      I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...