Jump to content
SAU Community

Recommended Posts

Alright, have a few things to sell, all this was going to go into my latest project but I have bought a new engine setup for it now.

Have, rb25det. complete inlet and exhaust side, missing turbo, has Greddy adjustable exhaust cam gear, full loom and ecu, loom has been modified previously, suit conversion. has coilpacks, injectors, etc.

Timing belt idler was a little noisey, so has been pulled off and is awaiting a new timing belt, haven't done this yet.

$1000 as is, or $1200 with new gates timing kit installed.

Z32 300zx gearbox (same gearset as RB25 r33 gearbox) with RB25 bellhousing on it, ready to bolt to RB20/25/30. good condition.

$1000

OS giken twin plate clutch, still heaps of meat left on it. comes with flyhweel, clutch plates, intermediate plates and pressure plate. good clutch. retails for around 2.5k

$650

Trust TD06 25g. Have the big td06 also, just been rebuilt, new bearings and seals, T3 footprint 16cm exhaust housing. great condition, will easily go over 500hp.

$1000

Nitto 40mm wastegate, brand new, all flanges included.

$150

Forged RB30 bottom end. ACL forged pistons, block bored to suit, crank linished, new bearings all throughout, RB25 oil pump, RB30 new waterpump, New rear main seal, comes with sump, ring gear, balancer, timing case. Ready for either RB25 or RB30 head.

$850

Can include full reconditioned RB25 head, 1.2mm metal headgasket, head modified to suit RB30 block, cleaned, decked, valves ground and seated, vacuum tested. Assembled on engine,

$1700 complete assembled RB30/25 motor.

BMW E36 318is Getrag 5 speed gearbox and clutch setup, Unneeded, box is perfect, clutch looks ok. Can come with twincam engine as well.

$700

All located brisbane CBD. contact buckna. 0427282562

Link to comment
https://www.sau.com.au/forums/topic/373987-rb25-rb30-td06-os-giken/
Share on other sites

Forged RB30 bottom end. ACL forged pistons, block bored to suit, crank linished, new bearings all throughout, RB25 oil pump, RB30 new waterpump, New rear main seal, comes with sump, ring gear, balancer, timing case. Ready for either RB25 or RB30 head.

$850

what rods?

still have the rb30 block? price shipped to darwin 0830? is the block all inclusive ie. pulleys, sump, crank,etc...

keen as to buy for a 30/26 convo. will have shipped to ballistic customs.

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...