Jump to content
SAU Community

Recommended Posts

Hi Alex,

It's a 1953 XK120 DHC. We are converting it to RHD. I believe ya mate because I too know very well there is alot of fixing. Especially due to the price range my dad buys them at :) They are such a rewarding car though that they are a pleasure to work on. Removing all the paint off the alloy bonnet and doors was just awesome. Removing the siezed door hinges and repairing was an absolute pain but a joy now that it's done. I could go on for hours on the things we have done so far just on one car. What car's did/does your dad have ?

Grew up with Rovers- P6B mainly, went through about 3 or 4 of them, then onto the honda rovers - quintet, 416, 827, and still has a 75. There was a daimler sovereign (like the 420 compact), a Mark1 Jag, nut and bolt (over 20 years...lol) resto on a MG A, MG Magnette was a bit before my memory, and finally he still has the early MGB GT, that his father bought new in England in good original condition.

He has a NA MX5 these days for the topless fun, all the joy of the MGA, without the pain.

+2 for liking the Chaser. Saw a JZX110 in Dandenong late Wednesday. Did like. Would consider buying if I didn't need/want a wagon.

Same; the boot was just too shallow for me; otherwise I'd be hitting some 1JZ action. The late model vvti single turbo 1JZ's are a much nicer thing to play with.

I still don't think the interiors are quite up to the standard of the Nissan though.

not really, i chipped my current car and its more economical and has more power............ :P

Gotta love the VAG cars for that. What chip did you get / who did it for you Iain, & what gains did they advertise for your car?

I bought the missus a A3 Tdi (125kw / 350Nm std) which I'm trying to convince her to let me upgrade the 'economy'. Most I've looked at don't get a lot more power, but some (supposedly) have as much as 77Nm gain - & that's significant considering how little effort it is to get it done.

not really, i chipped my current car and its more economical and has more power............ :P

+1 Iain; What did you end up using, and what is the end result?

Did you do any supporting mods?

Details man, DETAILS!!!

i got a 2nd hand superchips bluefin for $550. they offer a stage 1 (no supporting mods required) which does 54NMs more and 41HP. stage two can offer half again as much, but need fuel pump, dump pipe and intake. took 3 mins to reflash via a hand controller. ive done no other performance mods to the car. only HID conversion ($2.5k for HID pffft) and a fully integrated ipod interface to the satnav system.

leon, your wifes A3 if its more than 3 years old can do a remap via the consult, however all the new diesels (like andys) need to have the ECU removed and perform a bench flash.

i get boost from about 1500rpm and it wheel spins in the dry around 3k into 2nd gear. wet weather, forget about it. however this is a FWD car :( but it handles VERY well for an ass dragger. the sydney people will see it next weekend if they come to the meet

Edited by zei20l

That's a good price Iain. My preference so far is for Bluefin, but pretty pricey here in Aus. I don't know if I can buy it online from UK (running a special there atm) or if they'll insist I get it here.

And yeah, it's more than 3 yrs old so ridiculously easy way to gain some more grunt, umm, I mean better fuel economy, lol.

then you shouldnt have a problem with a reflash!

i got mine from www.vwwatercooled.org.au there is a good FS section there. i think the diesel engines have a good support forum too.

hahah sometimes economy=power. i can consistently get 10L/100km to and from work. highway, 6.5L/100km

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...