Jump to content
SAU Community

Recommended Posts

I'm currently looking for an R33 GT-R.

I've found some nice examples that have hit 120,000kms plus.

In general, how long do these engines last for? Do they reach 200,000kms without issues?

I worry as I have never heard of any RB26's reaching 200,000kms before :mellow:

I've only heard about the problems etc.

Should i be staying away from cars over 100,000kms?

I'm experienced with 4G's and 1J/2J's but i'm very new to RB26's.

Any help or advice would be greatly appreciated guys.

Cheers.

Link to comment
https://www.sau.com.au/forums/topic/376475-rb26s-with-higher-kms/
Share on other sites

As long they're looked after well, have solid oil pressure and not hugely trashed, they should be fine.

There is one 33 GTR on carsales that has done 347,000km.

Also don't ever take gospel on the odometer reading, for all we know it could have travelled more or less than indicated.

If seller claim it's genuine, ask for proof - i.e. Log books, de-reg/inspection certificate both here and Japan.

They can last million ks if its never been thrashed , perfect maintanace , kept standard etc etc. So the point is it comes down to the life its had and the current state which will determine its life.

Thanks fellas appreciate the information.

So a well looked after RB26 with 125,000km on it should be okay right?

And when getting a compression test done, what would ideal results be? (Just so i have a decent idea).

Thanks fellas appreciate the information.

So a well looked after RB26 with 125,000km on it should be okay right?

And when getting a compression test done, what would ideal results be? (Just so i have a decent idea).

Im no expert but i'd expect somewhere between 160 - 170 across all 6.

Just make sure they are all around the same reading and for example one is not sitting at 110 and the others are 170.

yep just like any car bring it to a specialist in the car and get them to do a thorough check.. racepace did mine and chris (the owner) looks over it with a fine tooth comb. they know absolutely everything about gtr's

Standard specs are 172psi, though i doubt u will find an engine with compression that goodanything over 150psi is good in my opinion, high 140's is probs stil okNissan workshop manual recommends a rebuild at around 125 from memory so anyting near there is not goodmake sure all cylinders are within 5% of each other

Standard specs are 172psi, though i doubt u will find an engine with compression that goodanything over 150psi is good in my opinion, high 140's is probs stil okNissan workshop manual recommends a rebuild at around 125 from memory so anyting near there is not goodmake sure all cylinders are within 5% of each other

dont know how correct you are there.. my gtr was all around 175 and i was there. and dont know if youd question racepace

dont know how correct you are there.. my gtr was all around 175 and i was there. and dont know if youd question racepace

You have an R34 and he has an R32. Yours will be much newer etc.

As everyone else in this thread has said, the condition of the car and getting a full inspection / compression test will tell you what you need to know... I would not pay much attention to the odometer.

As everyone else has mentioned ignore the KMS on the dash, look at the other tell tale signs of age such as:

- Right hand door wear

- Steering wheel wear

- Drivers side seat wear

etc..

If it says it's got 50,000km on the dash but the rest of the car doesn't reflect it then it's obviously not right.

Make sure you get a compression test done before you buy as well.

Also, when you start modifying don't go above 18psi or you will risk reliability.

As everyone else has mentioned ignore the KMS on the dash, look at the other tell tale signs of age such as:

- Right hand door wear

- Steering wheel wear

- Drivers side seat wear

etc..

If it says it's got 50,000km on the dash but the rest of the car doesn't reflect it then it's obviously not right.

Make sure you get a compression test done before you buy as well.

Also, when you start modifying don't go above 18psi or you will risk reliability.

not always. if it was owned by a larger person then all of those things will have more wear than a car owned by a skinny person. it also comes down to whether the car did short trips or long trips as a car that does shorter trips will have more wear from the driver getting in and out more often.

not always. if it was owned by a larger person then all of those things will have more wear than a car owned by a skinny person. it also comes down to whether the car did short trips or long trips as a car that does shorter trips will have more wear from the driver getting in and out more often.

Good point, all true. And also if the previous owner(s) wore rings there may be a bit more wear and tear on the steering wheel / gear knob, so not the best indication 4 u.

If you can, ask the seller if the 100k major service has been done (and have receipts). If I was buying a car with for example 70k on it, i'd probably be doing the 100k early as you cant really verify the km anyway (And like my mates r32 with 90,000 on it u might find a sticker saying next change due @ 200,000 under the cover.....)

If seller has no confirmation or receipts, maybe another negotiation point 4 u.

too many variables will affect how good a high k (or low k) 26 will be, like any used vehicle you may get lucky or you may have to open your wallet as soon as you get the car into your driveway

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm actually not sure - I think it was "Stealth Performance" (It really is near impossible to find a FEMALE 1/8BSPT to 1/8NPT male at ALL) but having the thing leveraged on a 90 degree angle on a small aluminium fitting is not too smart. Also in not too smart, I've drilled out the center of the broken fitting so there's maybe 0.00001mm of thread to bite into, so yeah. I may have to get it drilled/tapped/plugged entirely. Given I could conceivably tap a thread/adapter/pressure line in any point in the oil system I suppose it's feasible to run a line to the Nissan Sensor to keep the dash working. Do these exist in AN fittings and the like? Like an AN fitting that has a NPT (or other?) thread as well for putting a sensor in?
    • I would agree.  There will be an amount of boost you could run safely with an otherwise factory system, but it would be low enough to not be worth the cost.  And if you are reliving your 20s, you know a 'little bit' was never enough. Personally, if I didn't want to spend the money, then stick with NA bolt-ons, and maybe a tune.
    • Fuark, at least the motor survived. What brand was the fitting that snapped?
    • Wrong question. There's no point in spending the rather large sum of cash and effort to add turbo, without taking it to the "sensible" limit of the motor itself. If you have to upgrade injectors, etc, then so be it. That is a tiny fraction of what it will cost you to turbo it.
    • Measure voltage at the starter solenoid terminal when the key is at start and it has clicked. If it is really low, then the suspicion falls on the ignition switch (contacts or wiring thereof) as causing a voltage drop instead of sending enough volts to throw the solenoid all the way to engage the starter itself. If it is a decent voltage, then the suspicion is on the solenoid. Might have s horted coil, or might hva dirty contacts. Rip the starter off, dismantle, clean up contacts and inspect winding. It might not be possible to see if there is a short in the winding though. I have a spare starter here that I could measure the resistance of the coil, as a guide to about what it should be, if you need a comparison. <parts hoarder>No you cannot have it.</parts hoarder>
×
×
  • Create New...