Jump to content
SAU Community

Recommended Posts

Just out of curiousity where/what would you change in the tune to stop AFM cars stalling when running with a atmo bov/no bov causing flutter. I know you can tune it out as VL turbos and R31 redtop rb20dets never came with bovs and fluttered from the factory without stalling.

I imagine the cause of the stalling is where it runs very rich just after throttle off, would simply pulling all fuel from ~400rpm fix the issue? So when it stumbles it doesn't add even more fuel causing it to stall? Have any tuners looked at the stock redtop tunes to see what is different? I personally run the stoc recirc valve but I'm curious what the difference is.

One thing I have noticed is the redtop rb20s have a strange cylinder sticking out the intake that leads to nothing. This is post AFM and looks a bit like a buffer, could this be what they used to stop the stalling issues? Eg it buffers the fluctuations in pressure in the intake causing less AFM voltage fluctuation?

  • Replies 45
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

That would be a resonant chamber - just for noise tuning, although they can have a little influence on total power (in NA engines) by affecting the resonances in the inlet tract. I wouldn't expect any such effect upstream of a turbo however.

I would think that playing with the timing at the low rev high(er) load cells would be needed as well as fiddling with the mixtures. Kinda depends on what load cells it's actually accessing when the stall occurs though, because you wouldn't want to have to butcher the tune in those cells if they also happened to be cells that were accessed during normal operation, which is entirely possible.

because you wouldn't want to have to butcher the tune in those cells if they also happened to be cells that were accessed during normal operation, which is entirely possible.

Totally agreed, mainly why I mentioned the 400rpm cells as these would never really be accessed apart from when starting or the engine is stalling.

If anyone does have stock redtop rb20 maps, would you be able to look at these areas to see if there is anything stand out that might have been done for this reason?

Is this just an rb20 thing as Ive had my rb25 tuned with atmo bov (it was easier to install that way, less plumbing less fab) and I have no stalling issues, tuner did say the bov was quite good at staying closed and zero leak at the wrong times...

If anyone does have stock redtop rb20 maps, would you be able to look at these areas to see if there is anything stand out that might have been done for this reason?

Got any p/n's for ECU that came with bovless vehicles? I can check maps in Nistune and post 'em here.

Apparently some BOV users accept this fact.

And still have that little shimmer of hope that a girl will hear it, strip naked, and dive into their car. (Hopefully before it coughs up a heap of black smoke and stalls)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • GTSboy, thank you again. i’ve been reading all the other SAU RB25 vacuum line threads and you have the utmost patience for people asking “where do my vacuum lines go”. it’s appreciated. i did also enlist a few other RB guys local to me.  i would like to run 5 to 4. turbo pressure side to wastegate actuator. i would like to run 3 to 1. power steering air valve line to intercooler outlet. (this is how it was previously). i was told 2 is the bleed port for the boost solenoid - which i’m not running - so should be capped.   anyone see any problems with that?    
    • So yes. All of them. Something like 98% of all fuel in the USA has 10% ethanol: https://afdc.energy.gov/fuels/ethanol-fuel-basics It's labelled as like, AKI, 87, 91, 93 with an E10 or E5 or E15 label on the pump. At a certain point, it's not just "E10" instead of 91. It is 91, 95, 98, and all of them have 10% Ethanol in them. You can also get E85 and E30 which is why you do see some people rolling around with E30 tunes in them.
    • Thanks for the response. This is an 04 EP3 Type R. JDM spec. Fairly certain they're just basic BC racing coils. I do plan to keep as the ride quality on stock I've been told is pretty meh given Sydney roads. If I were to go down that avenue, does NSW require them to be a certain spec (close to original) etc?
    • Should have asked what is the car?
    • I've had two super conflicting experiences with blue slips. My 30 year old E39 waltzed through with no issues but my brother in law was knocked back on 12 y/o 3 series due to wiper blades and some cracking in a control arm bush.  What kind of coil overs? Do you want to keep them after?  If it was me I'd get some dirt cheap shocks and springs from eBay or scumtree. Not ideal but will get you over the line and might even be less than $1k.
×
×
  • Create New...