Jump to content
SAU Community

Recommended Posts

Anyone saw both Rota Grid and Varrstoen in real !?? I didn't saw both. I'm wondering which one look better. On some pictures the rota grid look frekain nice. on other, they just look like cheap toys with too much concavity.

The varrstoen, look nice but I heard the concavity depends on how large the rims are so a 9.5 will be more concave than a 9 inch rims. So I would like to know how much concave the 17x9.5 look like compared to the ria grid.

The varrstoen look to have a 1.5 inch rims and the rota a half inch lips.. I would prefer the lip of the varrstoen but would still like to have something concave.. anyone?

Link to comment
https://www.sau.com.au/forums/topic/378472-rota-grid-vs-varrstoen/
Share on other sites

Varrstoen Wheels Track 200 Series 2 are probably the best copied TE37's so far...

And the concave is still decent.

More subtle then Rota Grid's yet tough.

Varrstoen.jpg

Rota Grid's concave is a tad excessive / aggressive.

18x10s4lw1.jpg

364846080.jpg

I'd go geunine TE37's, but if you only want to chose between Varrstoen and Rota, go Varrstoen.

next set, varrsteon!

rota grids for sale if anyone is interested lol

wher ecan you get the vaarstoen from the US for under $900?

found these for $1094,

http://www.shop.cartel-aus.com/18-Varrstoen-221-Matte-Black-Alloy-Wheels-Var221MB.htm

here in the us. they run for 800$ shipped. haha! rota are even more expensive at 900-950$

I'm partial but I think like, after 3 month, I will get over the excessive concavity of the rota and would prefer a more rafined look like the varrstoen.

Varrstoen Wheels for $800 shipped?!

Dude WTF you waiting for?!

Go for it!

:D

  • 3 weeks later...
  • 3 months later...

What are you guys talking about, varrstoen wheels are cheap in Oz too - http://www.ebay.com.au/sch/items/_W0QQ_sopZ12?_nkw=varrstoen&_fromfsb=0&_trksid=m270.l1313 or look up varrstoen australia.. Or wasn't it in Oct 2011?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • I've never played with one, but I would expect that you are correct. That slot looks like it is intended to be used to unscrew the end, and the flats on the body would be better than grabbing it around the round bit with a pipe wrench. So, yeah, probably unscrews. You'll probably have to make a tool to drive in that slot.
    • A bit late but A disk S13P fit over stock R32 GTR brakes, usually A disk front, O disk rear works.
    • Or, the height of the release bearing is not correct for your combo. Start with the bleeding and checking the slave moves throughout its range when you press the pedal (2 person required), but it is possible for the height to be internally wrong too (box back off to measure.
    • Yes, there's quite a few things that can go wrong during a clutch install. Very unlikely. I have a similar clutch. They (ACS) make good gear. No, it is not normal. It is possible that you just need to bleed the clutch slave. But the new clutch will also have a more aggressive actuation force/pressure, and so your old slave cylinder might be a bit leaky or otherwise compromised, and not up to the extra force required. Or the master cylinder, same.
    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
×
×
  • Create New...