Jump to content
SAU Community

Recommended Posts

Ok so today I compression tested again so we have readings before and after the head gasket swap. Keeping in mind different compression testers have been used each time and todays tests were with A LOT healthier battery

Todays results:

Cylinder 1 being closest to radiator and 6 closest to firewall:

1. 170 2. 170 3. 162 4. 150 5. 167 6. 165

So cylinder 4 is down. I added a cap of oil and then got a reading of 172

Initial test carried out by mechanic before HG replacement:

No sure which holes they reffered to as 1 and 6 but im assuming its the reverse as what I've done?

1. 155 2. 160 3. 135 4. 145. 5. 160 6. 160.

Where too from here?

If it had a blown headgasket before and oil mixed with coolant. It will take ages for that oil to get out of the water galleries. You could flush the system 20 times and still not get it out. I'm betting it's just the old crap working it's way up to the top. It will ALWAYS end up at the cap and collect there. Try adding mineral turps to the system as that can help flush it through but unless the car is overheating and there is oil mixing through ALL the coolant, I'd say you have nothing to worry about

Is the oil milky?

No sign of water in the oil at all....

If it had a blown headgasket before and oil mixed with coolant. It will take ages for that oil to get out of the water galleries. You could flush the system 20 times and still not get it out. I'm betting it's just the old crap working it's way up to the top. It will ALWAYS end up at the cap and collect there. Try adding mineral turps to the system as that can help flush it through but unless the car is overheating and there is oil mixing through ALL the coolant, I'd say you have nothing to worry about

I like your theory but when the old headgasket was removed there were no visual signs of leaks or any issues on it anywhere according to simon. When the headgasket fails and starts mixing oil and coolant is it very easy to tell by looking at the old gasket once its out of the car?

Can someone run me through how I can flush the entire block and cooling system? Ive had a mechanic do it but god knows how well he did it... Im thinking radiator out and clean all that and run a hose into one of the lines and flush it for a good 10 minutes ect ect....

No sign of water in the oil at all....

I like your theory but when the old headgasket was removed there were no visual signs of leaks or any issues on it anywhere according to simon. When the headgasket fails and starts mixing oil and coolant is it very easy to tell by looking at the old gasket once its out of the car?

Can someone run me through how I can flush the entire block and cooling system? Ive had a mechanic do it but god knows how well he did it... Im thinking radiator out and clean all that and run a hose into one of the lines and flush it for a good 10 minutes ect ect....

The oil sticks to the cast iron, flushing with a hose won't get it out. It needs to be heated, mixed with the water, then when it condenses it will collect at the cap

Just keep cleaning it off each morning and keep monitoring it day to day. Eventually it will become less and less. If it gets worse, take it in to have it checked

Surely there has to be a way I can give it a good flush?

Spoke to one of the techs at MTQ today in regards to if its possible for the turbo to mix the oil and coolant. He said it is possible but hes never seen it happen. Only way to tell he said would be to remove the turbo cap off one of the water lines and attach a hose to the other end and turn it on and see if water comes out either of the oil lines.... thoughts?

  • 4 weeks later...
  • 2 weeks later...
  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
    • Well they got my money but they are not getting my gearbox ! 
    • It's needed for rolling idle up, and I think it is a decider on VCT also.
    • I mean, not really. Link ECU's can absolutely still have errors from the ECU thinking it's getting a sensor it's not expecting. I would imagine the speed at the ECU level in Nistune does absolutely nothing anyway? I assume the ECU does not do any fancy TC stuff with regards to front+rear wheel speed or anything of that like anyway. Someone who uses Nistune may be more fluent in it. 
    • Not yet quite as bad as what we've seen a Jim Berry clutch do in an R32 GTR though when it decided to cut a chassis rail in half... Still very very gnarly and a great reason to avoid.
×
×
  • Create New...