Jump to content
SAU Community

Recommended Posts

FOR SALE :

1998 R33 GTR VSPEC series 3 

KN6 (Dark grey/purple/blue pearl )

88,000kms

FIRM $28,000

Hello i have come to the sad conclusion that it is time to sell my Gtr . I have a few debts and Can no longer Afford to keep it . 

This is a fine example of a genuinely original S3 GTR . I searched a long time for a series 3 and came across this fresh from Japan . I am the first owner in Australia and it was complied and bought from NAGOYA MOTORS in May 2011 . 

1998 VSPEC which has ATESSA-ETS PRO unlike the standard Gtr r33 which have the non pro version , also this s3 has updated 4WD computers compared to s1/2 . The ABS module is also S3 only with 4 channel independent wheel abs (r34 Gtr) . A-LSD (active LSD) and few other mechanical differences I've seen across a few models .

The car is completely stock! I mean down to a Nissan tape player and no mods under the hood at all , the car remains as it was from the show room floor and the condition is also like new! 

I have lucky to fall upon an exhaust which is amazing quality , I only wanted to source the best parts which is why i went with FUJITSUBO GEIKEN. 

FGK Titanium (TUNED LENGTH) front pipe , it's a beautiful front pipe that has equally tuned length from both turbos , it wraps around the bell housing towards drivers side and joins back to the cat and sits tight on body.

FGK Titanium Catalytic Converter 80mm in/out , flat style for ride height . 

FGK Titanium Twin 60mm cat back . Sits tight and looks amazing underneath car , joins into a large ovel muffler and Still remains twin inside the body of muffler to a single 4" tip .

The car has been my pride and joy and I have done nothing but look after her . Since I've purchased the car I have had ZERO mechanical issues at . It seriously is like driving it new. 

I have taken it to WSID for a run down the 1/4 and got a time of 12.53 @ 178km/h . Which is amazing for factory trim . 

The boost is running 0.9bar and fitted with a xtreme HD ORGANIC clutch .

Call Glen on 0433818248

454d4065.jpg

2cd8b202.jpg

3434ac0b.jpg

78aaeeb5.jpg

f4a366d1.jpg

ff63c3d7.jpg

609cd6ec.jpg

c71fc627.jpg

86eb8d58.jpg

Link to comment
https://www.sau.com.au/forums/topic/378929-1998-r33-gt-r-s3-vspec/
Share on other sites

  • Replies 49
  • Created
  • Last Reply

Top Posters In This Topic

  • 1 month later...

Hi Mate, is this car still for sale - including the titanium exhaust system? I might have a buyer liner down here in Victoria. Just need to get him to have a good look over the car.

Cheers.

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
    • Neg, the top one is actually for the front. The sizes are 18x10.5 +18 and 18x11 +32.   I measured many times but I'm sure I'll have problems as this is the thread for problems.
    • Just one thing; tapping tapered threads is tricky. Taps are always tapered and you would generally run it as far as you can, but with a tapered thread you have to stop much sooner otherwise the wide part of the taper will run in too far and you will have to thread the sensor in too far too as well (possible that it will never make a good seal) BTW nice wide wheels, I guess the top one is for the back!
    • Welp, good to know. Will have to wait awhile until steady hands with drills and taps are available. In other news, these just arrived! I will weigh them for posterity. Edit: 11kg each (or 10.9/11.1 depending on what my scale decides over multiple tests, the 18x11 don't seem to weigh noticeably any more than 10.5)  
×
×
  • Create New...