Jump to content
SAU Community

Recommended Posts

Hi People,

I'm selling the following as I am now parting the car:

1) HKS Type R Intercooler (BRAND NEW in the box, havent even opened it). They are RRP over $1700. They have been engineered to maintain efficiency on applications rated up to 800HP. Very thick core, 700 X 304 X 103mm.

Asking: $1500 FIRM

p_hks-intercooler-kits-toyota-supra-turbo-1993-1998-r-type-.jpg

2) Defi Gauges (BRAND NEW, two taken out to look out and trial fit, the rest still new in the box) Comes with 4 gauges, Boost, Water Temp, Oil pressure and oil temp all in RED. Also comes with the Defi-link advance control unit.

Asking $1200 FIRM

600x450-2011051600004.jpg

350x600-2010012100010.gif

3) Volk Rays TE37 in BRONZE- (Used for only 2000km) EXCELLENT CONDITION, Not a single mark on them, built date in 2011. Measuring at 18x10.5 +15 all round, comes with Falken FK452, also around 2000km. These wheels in the classic bronze cost more then the SLs beleive it or not, but i do prefer the classic look.

Asking $3900 FIRM

dfdfsfsf.jpg

4) Tein Monoflex Coilovers (Near new, used for around 2000kms) Part Num: GSP72-F1SS1 (BCNR33)

Developed to be the future of axis of sport shock absorbers, used at circuit or on winding road. Its sport performance is sure to give a mental uplift to drivers. To meet various situations and to enable precise setting, Mono Flex has lots of know-how and technology poured in, such as newly designed platform and /or MSV (Micro Speed Valve).

FEATURES:

- The forefront of sport shock absorber, which can well perform at circuit.

- Use of MSV (micro speed valve) improves steering response and traction.

- Full-length ride height adjustment feature allows separate adjustment of the ride height and the pre-load.

- 16 levels of damping force adjustment (compression and rebound together).

- Teflon coating for rust prevention.

- Newly designed mono-tube platform.

- Pillow ball upper mounts are included.

- Compatible with EDFC.

- Available for overhaul.

Asking $1800 FIRM

Pictures coming soon

5) Quest R33 Tail lights - Custom made straight from Japan. Looks fantastic and really stands out from the rest. Cost me abit over $600. LED only on the brake lights, indicators and reverse lights have been left normal as i think it looks abit chat with it all LED.

Asking $500 FIRM

IMG_0615.jpg

6) BRAND NEW HKS T04Z Full Kit (RRP OVER $8000) - Comes with everything, manifold, wastegate, piping, turbo, turbo cover, dump pipe, etc.

Part Number is:

11003-an003

Exhaust Housing:

A/R 0.81

Asking $6700

IMG_3641.jpg

IMG_3639.jpg

IMG_3635.jpg

Edited by INLINE6
Link to comment
https://www.sau.com.au/forums/topic/379039-quality-japanese-parts/
Share on other sites

Sorry not willing to separate the gauges.

Just to confirm, intercooler is CORE ONLY.

HKS only sells the core when it comes to GT-Rs and if you want the extra bits it will cost around the 500 mark. The champs at HKS advised that the standard pipe is fine to work with the cooler itself.

i ordered one of these coolers a few months back, cost me more than that, and i had to get it from japan, cost me over 250 in frieght, so thats cheap as!!! good luck with the sale mate

Bump for the Qest Led Lamps !! :thumbsup:

I know the Qest company owner quite well and these are quality lights and he only uses the best quality Japanese Leds.

Housings are genuine Nissan so they are a perfect fit !!

Plus they look bloody good.

Bump for the Qest Led Lamps !! :thumbsup:

I know the Qest company owner quite well and these are quality lights and he only uses the best quality Japanese Leds.

Housings are genuine Nissan so they are a perfect fit !!

Plus they look bloody good.

You know the owner...

Pls enquire about ones that look that good for R32 very interested.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
×
×
  • Create New...