Jump to content
SAU Community

  

69 members have voted

You do not have permission to vote in this poll, or see the poll results. Please sign in or register to vote in this poll.

Recommended Posts

  • Replies 138
  • Created
  • Last Reply

Top Posters In This Topic

Your wagon would be a contender.

only if i put spinners on the back and got a few panels in different colours

they could also have the kimi award, for the first person to tell a commentator they were having a shit

only if i put spinners on the back and got a few panels in different colours

Don't forget a "UNIT" sticker. And remove your back springs for instant lowrider status.

Can I enter a rotary at this event and get a trophy to prove I’m a real WANKR, I will drop oil everywhere, blow big flames and drive up and down the pits revving the crap out if it.

Yes, yes, yes Brian!!! Then we can have a "Wankr with a Wankel" award, right Fatz?

so what sponsors can we get?

I think with all the blow ups and crashes insurance companies can get involved.

we'll need to wind back some odo's with some cars too - anyone got any contacts?

so what sponsors can we get?

I think with all the blow ups and crashes insurance companies can get involved.

we'll need to wind back some odo's with some cars too - anyone got any contacts?

Most of you would know Baron and myself know the crew at TengaEgg.com quite well, but what you may not know is I'm also a Top 10 client at Tug Toner (Baron is #3)..... Here's a vid if you're unfamiliar.

http://www.youtube.com/watch?v=POXMAiLZhOg

my balls felt like that once when i snagged the on the side of the race seat

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I've never played with one, but I would expect that you are correct. That slot looks like it is intended to be used to unscrew the end, and the flats on the body would be better than grabbing it around the round bit with a pipe wrench. So, yeah, probably unscrews. You'll probably have to make a tool to drive in that slot.
    • A bit late but A disk S13P fit over stock R32 GTR brakes, usually A disk front, O disk rear works.
    • Or, the height of the release bearing is not correct for your combo. Start with the bleeding and checking the slave moves throughout its range when you press the pedal (2 person required), but it is possible for the height to be internally wrong too (box back off to measure.
    • Yes, there's quite a few things that can go wrong during a clutch install. Very unlikely. I have a similar clutch. They (ACS) make good gear. No, it is not normal. It is possible that you just need to bleed the clutch slave. But the new clutch will also have a more aggressive actuation force/pressure, and so your old slave cylinder might be a bit leaky or otherwise compromised, and not up to the extra force required. Or the master cylinder, same.
    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
×
×
  • Create New...