Jump to content
SAU Community

Recommended Posts

I am selling my RB26/30 motor built by Subzero Racing.

Spec's include...

Bottom end line bored, o-ringed, heat treated, lunati 4340 rods, forged pistons, chrome moly rings, ARP bolt's, crankshaft balanced and nitrided, engine deburred and blue printed, nismo water pump, RB26 head serviced, race ported, TODA cams 10.2 mm lift 282 deg duration, TODA cam gears, ARP head stud kit, custom Subzero plenum, chrome covers, custom dry sump (does not include pump just the sump itself) or wet sump.

Subzero guarentee's 1000hp. Same motor powered TRY09's to 9.46 @ 151mph.

Sell $13,000.

I'm on the Gold Coast, QLD.

Mob: 0403 185 817.

Conditions of sale: cash only, pick up only.

Cheers

Aaron.

post-192-1131252238.jpg

Edited by PVL-747
Link to comment
https://www.sau.com.au/forums/topic/38089-rb2630-for-sale-will-handle-1000hp/
Share on other sites

  • 3 months later...
  • 1 year later...
  • 7 months later...
wasn't this engine sold about 1 month ago

Are you serious? You reply to an 8 month old thread asking that question?

date='5 Nov 2005

Thread closed...

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • Thank you, 100% the intent. New coils were due and the 17" sixers look/feel loads better than the stock wheels. The aero options are so spot on.   Thanks for the warm welcome, all!
    • 98 r34 gtt Been rocking my latest setup and car running like never before. Have put a good 200 miles on it since all the latest changes and additions. everything is dialed in and have been driving it a bunch.   However, all a sudden last weekend as soon as I pushed throttle passed 4k and the engine stumbles, (slow or fast acceleration) hesitates and doesn’t go above 4100 or so, like a misfire. Everything else seems fine. I had a “good” set of coil packs that I removed from car when I first got it when I changed them over to new coils. I swapped out current ones for those, but no change. I also changed the plugs, no change. Seems to rev over 4 when out of gear with no load just fine no “misfire”, but as soon as its in gear with a load of any kind, it “misfires” as soon as rpm drop back below 4 k it runs perfectly, smooth, starts, restarts and drives fine as long as I keep it below 4 k while in gear. All readings look fine, no CEL   Any idea as to what could all a sudden cause an issue when pushing rpms passed 4 k?
    • When you say your cams are 272/262 is that 272in and 262ex?
    • We're arguing semantics. I am saying 45 accel and a 55 deccel ramp are "2 ways". Even a 45 degree ramp and an 89 degree ramp is "2 ways", because it is literally... two ways. The cusco 55/30 ramp is a 2 way. It's two ways. I get it though - in normal nomenclature a "2 way" would be 45/45 or 55/55 or 60/60 i.e the same locking in both directions. And something like 45/65 would be considered "1.5 way". I would then say if we're getting into the nitty gritty then every locking diff is a "2 way" diff and we should not speak in 1.5, or 2 ways but ramp angles instead. Which ofc if one of those ramp angles is 90deg, that side is not doing any locking. :p So Nismo don't obviously sell 3 things. The fact of the matter that they only sell two items really goes to show that there's a 2 way and a "1,5 way" which is really a 1 way. I believe the actual lockup for the 'adjustability' of the GT pro is really just setting preload for when the ramps actually start locking up. It's not changing how much 'wayness' there is. It is (somehow) horribly explained. People just buy whatever diff and go "locks up good bruh" and that's what ends up on socials forever.  
×
×
  • Create New...