Jump to content
SAU Community

Recommended Posts

  • Replies 886
  • Created
  • Last Reply

Top Posters In This Topic

  • 2 weeks later...

Ok I'm sick of reading different opinions. What is the consensus on running in a rebuilt motor. I would like a step by step from the moment I pour water and oil into it if possible. I don't want there to be any chance of me stuffing it up.

Thanks in advance.

I recommend you get someone to do all the work for you with warranty, otherwise I reckon we'll be soon reading another thread titled 'fresh engine installed, but still having problems'

ok so here is some more info, one of my valves in cylinder 5 was about to drop in, and my head has marks from where the head gasket was soon to blow. so looks like i pulled it down just in time. on another bad note, when i had my front guard replaced a few years ago they dodged it up and used a holden indicator bulb holder and just electrical taped it on to hold it together so now my clear indicator housing wont work :@ another call to just cars to get more repairs done, glad they have life time guarantee on repairs. this is the 4th time it has had to get repairs done.

and a strange question. i need to provide my stem seals and cam seals for the head to be re assembled, in my gasket kit there is a packet with 12 stem seals, a packet with 12 stem seals and 1 big seal (looks like a cam seal to me) is there only supposed to be 1 cam seal? the only other seals in the kit is a packet with 2 seals the same as the cam seal and a rear? oil/main? seal. could one of these be the other cam seal?

Why would you strip an engine down for a rebuild and use 2nd hand parts if unsure of the condition?

If you can replace it and your not sure of the life condition...replace it while you can.

Last thing you want is a fresh built engine, 2nd hand oil pump, final tune, youll head out and give it a boot full and

hit limiter a few times and then the collar or something fouls

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • It might be worth having a good look at the chassis behind the bumper then; most people prefer the series 2 look so it might have been changed to cheaper parts as part of an earlier repair
    • The car itself a series 2. I was just curious about the headlights and just wanted to confirm that they were series 1. Good to know the rest of the front end is series 1. It’ll be easier for me to find parts on the aftermarket side of things lol
    • If you've wired up the coils & injectors properly, & have the neo CAS loom for the trigger, it should all work. The VCT works the same way so just different plugs between s1 & neo. Assuming DBW if no IAC. Don't bother with the stock boost solenoid with g4x.
    • THERE IS NO IAT SENSOR ON ANY SINGLE TURBO RB. And the one on an RB26 is not for "engine control" - it's really too big and too slow and is only used for over-temp alarming (as far as I can tell). Anyway, you don't have one. You want/need one for the Link, then you need to buy one, find a spot for it, and wire it in. You do know that the stock boost solenoid is not capable of "control", right? It is merely on or off, for the low boost (5 psi) and high boost (7psi), which the ECU enforces mostly based on gear. The stock solenoid is not for PWM control and is not plumbed up in a way to provide it. If you want to control boost properly, then you need a proper MAC valve. And yes, you can wire either of them direct to the ECU. Well, I assume you can - I don't know what the boost solenoid pins on the plug and play Link are capable of. They really should be as capable as any normal Link - but seeing as it is plg and play, it might be limited to stock functionality. Read the doco.   You really do just want to plug stuff together without understanding how it works, right? I can't help you there. I don't know the plug types or pinning on half the stuff you're asking about. If I had to do it I would sit down with the wiring diagrams, the car/looms and a multimeter and work out what is what.
    • Light should be a pressure switch, not a sensor.
×
×
  • Create New...