Jump to content
SAU Community

Recommended Posts

  • Replies 886
  • Created
  • Last Reply

Top Posters In This Topic

  • 2 weeks later...

Ok I'm sick of reading different opinions. What is the consensus on running in a rebuilt motor. I would like a step by step from the moment I pour water and oil into it if possible. I don't want there to be any chance of me stuffing it up.

Thanks in advance.

I recommend you get someone to do all the work for you with warranty, otherwise I reckon we'll be soon reading another thread titled 'fresh engine installed, but still having problems'

ok so here is some more info, one of my valves in cylinder 5 was about to drop in, and my head has marks from where the head gasket was soon to blow. so looks like i pulled it down just in time. on another bad note, when i had my front guard replaced a few years ago they dodged it up and used a holden indicator bulb holder and just electrical taped it on to hold it together so now my clear indicator housing wont work :@ another call to just cars to get more repairs done, glad they have life time guarantee on repairs. this is the 4th time it has had to get repairs done.

and a strange question. i need to provide my stem seals and cam seals for the head to be re assembled, in my gasket kit there is a packet with 12 stem seals, a packet with 12 stem seals and 1 big seal (looks like a cam seal to me) is there only supposed to be 1 cam seal? the only other seals in the kit is a packet with 2 seals the same as the cam seal and a rear? oil/main? seal. could one of these be the other cam seal?

Why would you strip an engine down for a rebuild and use 2nd hand parts if unsure of the condition?

If you can replace it and your not sure of the life condition...replace it while you can.

Last thing you want is a fresh built engine, 2nd hand oil pump, final tune, youll head out and give it a boot full and

hit limiter a few times and then the collar or something fouls

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • New or used transmission? Alignment will be the same with engine running or not. If new, i'm presuming it's a clutch release bearing size issue. If used, are you certain it's a CD009/A and not an older CD008 or less? They had known synchro issues. In my opinion, these transmissions should always be purchased new, they're dirt cheap and you avoid dealing with old revisions. 
    • I like your thinking! Looking forward to see how it turns out.
    • You've got yourself a good old game of have fun. That shit is annoying as hell to remove. Thankfully for you, yours is on metal, most of the stuff I take it off is plastic, so typically hear guns are out. I normally end up continually dragging my thumb with pressure over it to get it to peel up. Eucalyptus oil then works well for getting residue and last remnants off.   Edit: plastic scraper might be worth while too. One that'll dig into the foam tape, but not scratch the paint.
    • So I ride and race motorcycles for fun and have always used a van to transport my track weapons. Figured towing a racebike with a skyline would be different and if done right could - "look fully sik" or quite cool for us grown ups lol. Pic of yours truly on two wheels I also have a trailer already kitted out to transport my bikes ...and I have a spare set of rims that match the car that I was going to rebarrel to get deeper dish at some stage but they have just been gathering dust. Sooooooo it is only logical.... Stay tuned !!    
    • If by "flap disc" you meant "chocolate wheel".... then they are OK for getting off stubborn remnants. But not for stuff with bulk depth. If by "flap disc" you meant "abrasive paint f**ker"....
×
×
  • Create New...