Jump to content
SAU Community

Recommended Posts

we already have a resident R31 to poke poke fun at. Actually, its moreso the driver that we poke fun at than the car.

I believe Ash's R31 coupe n possible ACSplits R31 and SKY031's car will be there too.

  • Replies 205
  • Created
  • Last Reply

Top Posters In This Topic

Winery The winery is a really nice small winery and I personally sampled both the merlot and shiraz over the weekend. Beautiful drops. This will probably be the best place for photo's for the day as the back drop looking over all the vines was pretty impessive.

hm winery that might give the missus an excuse to come and the western ring road is only round the corner I'll be there at least in the super pimp ceffy.

cheers

meggala

[silhouette]']Hey guys,

just wondering any R31's gonna be on this cruise?? I dont wanna be the only one that everyone points and laughs at : )

Cheers

[R31][silhouette] Silvertop Rb20det

dude, im coming in a ford raider 4wd!

DISTANCE UPDATE: Total distance is 270km - from start: WRR Mobil (Synergy 8000) to finish: Calder FWY BP (Ultimate).

The only town on the route with premium is Dalesford (Optimax). If my car can make it with a full tank from the start point, everyone else should be fine :P

James, Ash and Andrew hope you planned a couple of rest stops along the way, as shivam and myself went for a test run yesterday and he experienced major brake fade just after the down hill sections. Jumped out of the car to see the front calipers SMOKING :P.

The area was GREAT and had alot of fun. Should be a top day!

Ah - thought that was you! I was in a blue/purple Subaru Liberty coming down Mt Macedon cross as you were going up. I had my head/driving lights on :P

Was out taking photos of the major road signs to help with directions.

Will email you full map/photos/route notes during the week... and yes, some good rest stops :)

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..    If i get this - will this fit all around: Size: 18 x 8.5 +37 - n what tyres size tyre should i get for front n back?  
    • Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...