Jump to content
SAU Community

Bris: Big Brake Kits

martz
 Share

Recommended Posts

martz Contributor

martz

Posted
Posted

Hi Guys,

just wondering where one would go to purchase a big brake kit? my 350Z is currently in CNJ Motorsports and advised me that my rotors need to be replaced so I thought I'll take the opportunity to upgrade (I'll need it anyway for better stopping power). I'm currently running the touring version stocko brakes (non-brembo)..

Thanks.

Martz

Link to comment
https://www.sau.com.au/forums/topic/382049-bris-big-brake-kits/
Share on other sites
martz Contributor

martz

Posted
  • Author
Posted (edited)

I don't intend to track (but you never know) but definitely will be doing a lot "spirited" driving.

Rim sizes are 19x9.5 front and 19x10.5 volk racing wheels.

Budget would be 5k total for the front and rears.

Edited by martz
Roy Grand Master

Roy

Posted
Posted

Its a 370Z front end. The brakes are the old CSC, then B-Spec and now ARK designs. The design has not changed, though rather then painting they are now hard anodising the calipers. They still prove to be good setup with quality rotors, a sort of Harrop copy caliper that uses a Porsche Pad. With Harrop, Stoptech and others using Porsche pads there is a good range of compounds available.

You may just get the front and rears for 5k

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      Dose's Sometimes DIY and Pay Someone Home & Boat Improvement Thread

      By Dose Pipe Sutututu · Posted

      Wife wanted basket things in the wardrobe in our temporary house. Thought about ripping our the wardrobe and fitting the entire IKEA set, but it's a temporary house and we want to move in a few years. So IKEA advertises this as a 50cm unit, however the actually basket and rails measure 46cm wide. Only issue was depth, IKEA stuff is quite deep, where as the builder special junk is super shallow at less than 40cm. Send it, chopped the rails, then offset the mounting holes, job done, happy wife, less shit scattered all over the bedroom. Did the same to the other side too. Also drove the Skyline shit box today, dropped off oil at Supercheap Auto. I didn't realise they only now take max 2x bottles per visit. I visited 2x Supercheap Autos.  
    • Kinkstaah
      Strange issue RB25DET wont start

      By Kinkstaah · Posted

      I've seen similar actually in my situation. You never know what tables are attempted to be used when the car thinks it's -99C or +200C. The fail state is not usually that extreme but you know what I mean - it was in my case though! This is where being able to read all the sensors is useful cause you see this stuff really quickly.
    • Kinkstaah
      First time Skyline owner

      By Kinkstaah · Posted

      The above is very important. However as long as you keep timing relatively low, it's plausible to make your own knock ears and plausible to learn to tune with a modern ECU that can do wideband O2 correction like a boost controller. I mean if you only have one viable road to even drive the car on, learning to tinker to this level may be worth doing given you can't do much else with the car...?
    • Kinkstaah
      Chris' Toyota Mark ii JZX110

      By Kinkstaah · Posted

      I find the fact that the rear plate has to be bent inwards at the rear not so bad: but the front is just awful: It's like come on. (these are my very old, now retired/turned in plates) TBH it is a lot of money to fix a minor issue, the fact I said "I'll never really spend the money on doing this" is why people ended up buying them as a gift for a 'car guy' who can be hard to shop for.. for car guy things.
    • GTSBoy
      Chris' Toyota Mark ii JZX110

      By GTSBoy · Posted

      I just bent the ends of my premo plates. It even went through Regency like that after the engine conversion and the inspector (a great bloke!) just squinted his eyes and said "I didn't see that". Plates, and how they look, are just something that have zero importance to me.
×
×
  • Create New...