Jump to content
SAU Community

Recommended Posts

if its been brought up before plz direct me to the post, but if it hasnt...

living in australia, im looking @ around 35-40K for a R34 GTt.

found one in NZ for 20K..

does anyone have any idea why there is such a difference in the price of cars?

also if i can be a pain in the ass, are we able to import cars from NZ to AUS? if so, will the cost of improting not be worth the trouble?

thx :>

Link to comment
https://www.sau.com.au/forums/topic/38342-nz-cars/
Share on other sites

If you buy a NZ new R34 you are still looking at the 30-40K price range, but any of the imports are much cheaper. When I was looking around for a skyline I was going to get a 34 but when you are looking at one for 20K it will have done around 160,000km so it was much better to get a modified 33 for less.

Link to comment
https://www.sau.com.au/forums/topic/38342-nz-cars/#findComment-777309
Share on other sites

Looking at the range of 2nd hand Jap imports available there, I'd say NZ has a more relaxed import law. I read somewhere that the compliance cost is much less...like under $2000.

Correct me if i am wrong, from observation...NZ allows the import of vehicles that had been sold locally as well. E.g. the S14 & S15 200sx - consumers in NZ can import the S14 & S15 Silvia's?

Someone posted a R34 GTT brochure in this forum short while ago...and notice that this brochure came from Nissan dealer in NZ. - Surprise to find out that R34 GTT was available as a brand new import there.

With Oz, it is not just tryin to protect market dominated by Holden & Ford, also others like local Nissan, Toyota & others. Looking at theMarch sales figures in Saturday's motoring section in The West Australian, I'd say they are doing PRETTY darn well despite the no. of 2nd hand imported.

Overprotection just doesnt make sense to me.

Link to comment
https://www.sau.com.au/forums/topic/38342-nz-cars/#findComment-777334
Share on other sites

You can import anything you want over here. No restrictions on models or anything, Just had to be post '96 unless the car had recorded frontal impact testing if it is pre '96. The main problem we have here though is that unlike australia cars do not hold their value due to being able to get anything you want from Japan for bugger all. I know it is possible to import and register etc an R33 GTR for around NZD 20,000.

Link to comment
https://www.sau.com.au/forums/topic/38342-nz-cars/#findComment-777344
Share on other sites

If you buy a NZ new R34 you are still looking at the 30-40K price range, but any of the imports are much cheaper. When I was looking around for a skyline I was going to get a 34 but when you are looking at one for 20K it will have done around 160,000km so it was much better to get a modified 33 for less.

Body: Metalic Silver 2-door Coupe

Odometer: 77,500 Km

History: 1 owner, Imported

Engine: 6-cylinder 2500cc Manual

Fuel: Petrol

Number plate: BNA154

W.O.F: Expires Sep 2004

Registration: Expires Sep 2004

Stereo: Top factory stereo with 8" LCD screen

Features: ABS brakes

Air conditioning

Alarm

Alloy wheels

Central locking

Driver airbag

Passenger airbag

Power steering

Turbo model engine RB25DET NEO

Extremely nice vehicle to drive with a factory 280 horsepower.

Factory extras including traction control, UV cut glass, xenon crystal headlights, dual airbags etc

Top of the line alarm system.

Fully Automatic LCD Screen to control the audio system.

Meticulously kept vehicle.

this is the 20 000 dollar car.. $17300 AUD

Link to comment
https://www.sau.com.au/forums/topic/38342-nz-cars/#findComment-778311
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...