Jump to content
SAU Community

Recommended Posts

Hey,

I Bought a set of tomie cams for the RB30DET but there was a mix up when the company i bought them off and I cant get onto them to recterfy the problem.

So I have a series 1RB25DET head which had a metal CAS on it. The cams I received look exactly the same (apart from lobe) and also the alignment key for the CAS. I believe they are series 2 cams as I heard the neo cams run shim n bucket.

What I want to know is will I have any problems installing these cams and plugging in a series 2cas?

I had a search on the forum and couldn't find what I was lookin for.

Thanks in advance

Adrian

THE-31

Link to comment
https://www.sau.com.au/forums/topic/383493-rb25det-cas-s1s2/
Share on other sites

Yeah the search bar isn't the greatest but, it's not only poncams I was looking for it's just if someone knew about std neo cams running in a s1head.

But think I've found out now I just have to swap the wires around when I run the neo CAS.

Thanks for your help with it all.

  • 8 years later...

hello guys,who has 100% answer,not the internet search one,about repining of CAS.I need to repin R33 Mitsubishi Cas to R34 Neo Hitachi Cas,i found several answers,so which one is the correct one?Most common answers are that R34 Hitachi Cas plug is the mirror type of Mitsubishi one,is it prooven?Alot guys write,that some CAS'es need trigger wires switched,while power and ground are same,can somebody confirm one or another?

ePnzj8d.png.224145526f5c0e13b50a72f9bc04675c.png

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I can get more photos of it here soon and I plan to make a thread detailing the process. I received the car this way and it sorely needs refinishing. That is probably the most appealing photo of it. Up close it is fading, cracked, and needs to be re-glued. Depending on their condition I'm on the fence between refinishing or making a new set.  Another angle hiding the pimples and razor pumps  
    • According to this thread the RS4V with build plate RC40 comes with the R200 diff @ 4.083 ratio as well (mine has said RC40 denotation). We may need to check if the axle stubs are the same pattern as well. The auto subframes have longer axles. However I think yours being a later Series 2 as well, we should have the same bolt pattern for the diff stubs. Unless your upgraded rear also has upgraded axles. Either way, I would not be opposed to pulling the covers to check so I can inspect that  fancy rear core  Also I don't have HICAS. I don't believe that should change things but I hope the people here with heaps more experience than me can correct me if I'm wrong   Let me know if you want to attempt to make this work and I can get some pictures of mine from under the car. 
    • It's not that straightforward. For example I have had this code because my ignitor/power transistor wires were unplugged. It knows something is wrong but has no idea what it means. If you want to actually diagnose this I recommend following the service manual flowchart for code 21. Ohm out the harness, coilpacks, inspect the ECU, etc. And again, it's entirely possible for there to be no problem at all but if you're running a different coilpack it'll trigger the code because it doesn't like what it sees.
    • If it (the code) wasn't still current, it should have gone away by itself by now. No, nothing it 10/10. But it is quite likely. Everything else to do with the ignition could still be responsible (which is wires and connectors). The car is an old piece of shit now, so all the wires and connectors are also old pieces of shit.
    • Lock me in mate, although I'm not sure if I'll be heading up from Goulburn or down from Sydney, either way, return will be back to Goulburn 
×
×
  • Create New...