Jump to content
SAU Community

Recommended Posts

I was wondering what would be a reasonable but yet powerful turbocharger to substitute the stock one that comes with a rb25det neo, i am aiming to get my r34 over 300rwkw,

current mods:

x-force turbo back system

k&n apollo cold air intake

Any help is appreciated :)

Link to comment
https://www.sau.com.au/forums/topic/384116-turbo-upgrade-rb25det-neo/
Share on other sites

Mate there is a lot of things to be done to your engine besides just bolting on a new turbo to get this sort of power....ie supporting mods - injectors, fuel pump, intercooler, boost control, engine management to name a few.

you want to spend 2k max, not laughing at you but id atleast double that amount to achieve your goals reliably.

Mick

was preferring something less expensive since i dont have a vast budget, something under 2k? pinch.gif

under $2k total eh.....

Do you have any thoughts on what engine management, injectors, fuel pump, FMIC you are going to buy to get to 300rwkw?

To clear things up, i just started researching and planning my mods, im willing to spend more but i am looking for a turbocharger under 2k.

As in supporting mods go:

Fuel pump with regulator + hks fuel rail kit

Front mount

Apexi power fc

Thats naming a few too, saying that i need clearing up on what is the right order regarding those mods. If you guys can suggest other supporting mods and an order, that would be great too

Budget setup cant go wrong with a kinugawa td06sl2 20 or 25g $850

ebay s/s high mount manifold $220

40mm or bigger ext gate $300

Walbro fuel pump $130

Deustchwoeks injectors (or highflows) $450

Z32 $200

Nistune $1000

Fmic kit $400

Rough prices on parts but that will basically get u to 300rwkw.

You do not need a hks fuel rail.

ebay manifold???

deustchwoeks injectors???

walbro fuel pump???

40mm or bigger gate

can you get anymore crap parts in one post?? jesus...

oh and of course it just has to be a 35R and highmount to make over 300rwkw doesnt it, cause thats just so cool eh...

total crap...

Thanks for your time guys first of all, i also got a recommended a GT3076 or a ATR43G3 FNT they are both easy to install with minor modification as long as bolt in goes, so i guess it would be a choice out of the two. How would i go about finding a high mount manifold?

Lol...high mount manifold for 300RWKW.

IB4L and "Thread closed. Believe it or not, but since SAU started more than 7 years ago, this topic has been discussed before....."

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Mixing things up - installed some leather recaros to match the leather seat covered rear seats. Interior looks pretty schmick now except for some slight wear on the steering wheel which I will monitor and address if it becomes worse or actually noticeable!  
    • Didnt realise RB's had more then 1 head.
    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
×
×
  • Create New...